FFHT1621QS6 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic drawer support had broken from extended use.
This was a truly easy snap-in repair. Because I live in a small fishing village on the coast of Venezuela, the only difficult part was waiting for the part to arrive. I'm very grateful that Part Select makes ordering parts easy and reliable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lancaster, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cheese drawer rail broke
I took out the screw and removed the old rail, then I used the same screw to install the new rail. It took me 2 to 3 minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
Both support rails had broken
First, remove shelf unit from refrigerator and lay glass side down on a large flat surface. Observe, then pay attention to assembly. Spent more time with this, drinking coffee, and playing with puppy, than the actual repair. Only had to remove and replace two
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Center Point, IA
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Left rail was broken
The shelf needed to be removed from refrigerator and then remove the screw and pull the rail from the bracket on the opposite end. After installing the new rail it turned out to be a fraction of an inch too long so I had to file the cracket on the shelf which is metal. The rail slipped back in and was perfect. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Rockland, ME
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
draw support broke
detached with screwdriver and applied the new one the same way. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Olive Hill, KY
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Support rail broke
I took the shelf out and took part off and replaced the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorphial from Arcadia, FL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drawer Support Rail Left Side Broken
The Hardest Part Was Taking Everything Off The Shelf,Took Old Part Off And New Part Popped In And I Tightened The Screw And That's It Done!Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
Broke The Draw Slide Stop Off The End Of Lft Hand Rail
Took all the item off the shelf turned it upside down on the table,worked rear off off the pin carefully,install new rail and refastened the front tab strip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cyprian J from Bradenton, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
We had a broken drawer for the lunch meat storage
No problem, got the part promptly and it was the right part and easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rio Frio, TX
- Parts Used:
- 5304506471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
2 Screws, done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Sarver, PA
- Parts Used:
- 240313703
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Was this instruction helpful to you?
Thank you for voting!
Drawer Supports Broke
In 10 years, this is the second time these drawer supports broke and what a difference to fix. The parts came quickly, fit well and are very easy to install. The fridge is good as new and the cheese/condiment drawer is back where it belongs. Good quality and easy to do.
Was this instruction helpful to you?
Thank you for voting!