FFHT1621QS6 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No cool in lower refrigerator
I’m a technician,I was contacted by a customer. After listening to the customers issue I determine the freezer evaporator fan was bad. Real easy job loosen the hex head screws on top of the ice maker and pull it straight up. Disconnect ice maker wiring harness.remove the two top 1/4” screws that hold the back cover on and pull it forward. Disconnect your wiring harness and remove the whole back panel. Lay the back panel face down on the floor and remove two metal clips that are up at the top with a flat head screwdriver. Center plastic panel slides up and out maybe necessary to take a flat head screwdriver to the very top to release the plastic clip. Pull your fan blade off. On the backside of the motor just take and twist the flat plastic piece counterclockwise and remove your motor and install the new one Reassemble in the opposite order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jaime from Harrisburg, PA
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked drawer
I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Cannon Beach, OR
- Parts Used:
- 240383801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A shelf in the refrigerator was broken off by a renter.
It was very simple - just had to pop the part in. Delivery was quick - very slick!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from Winsted, CT
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the drawer support rail broke
it was very simple, my husband did it. had to take the top shelf out and screw in the support rail and that was it. couldn't have been any easier. this was the easiest process from start to finish that we ever had. looked up on line, found your website, ordered the part and it arrived in a couple of days. So easy and your company was most efficient in having the part and in processing. Couldn't have been mored pleased.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SYLVANIA, OH
- Parts Used:
- 240597220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from BOURG, LA
- Parts Used:
- 240530601
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic support rail broke
removed the top shelve. Unscrewed the broken support rail and replaced it with the new one.Put the shelve back and I was done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arnett from PHILADELPHIA, PA
- Parts Used:
- 5304506471
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My refrigerator door handle connector bracket broke.
I order the handle kit. I removed the old handle by unscrewing the old and installed the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Sayreville, NJ
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Job was really easy. Took less than 10 minutes
I easily removed the shelf, cleaned it, removed one screw, adjusted a tab that was bent, then installed new side rail with the screw that was removed and put back the shelf and storage bin. Everything worked perfectly. I must have saved $100 by doing it myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Minneapolis, MN
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing door rack
Just snapped them into place without any problems! The parts were exactly what I was looking for.
Was this instruction helpful to you?
Thank you for voting!
Left side rail support snapped off the lunchmeat drawer
Used a small screwdriver to disconnect the left side rail from and replaced with the new left side rail. Everything went smooth and from start to finish, replaced the piece in about 3 minutes. Works great now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Port William, OH
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door rack broke in half
opened thepackage snapped in place .took all of 3 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Chicago, IL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Left Support Rail broke
Most of my time was spent removing food items from the shelf that supported the rails. Once that was done, a quick removal of the screw, replace the left support rail and re-installing the screw. Done. I wish all of my repairs were so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Toledo, OH
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Too much weight in lunch meat drawer
Emptied the shelf. Took out the shelf. Screwed in the one screw for the support rail. Put shelf back in. Put drawer back in. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!