FFHT1621QW2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from GRANADA HILLS, CA
- Parts Used:
- 5304506469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
HANDLE BROKE AT THE SCREWS
On screwed the screws, slipped the guide over the bottom screw, re-inserted and screwed on the old screws. It took two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from TORRANCE, CA
- Parts Used:
- 240383901
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Shelf Bin broke....A++
Got it replaced and was easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- xingju from CHICAGO, IL
- Parts Used:
- 5304506469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no problem
remove old handle,screw the new one.
Was this instruction helpful to you?
Thank you for voting!
My refrigerator had a broken rail for the meat drawer and also the bottom door rack had cracked.
The parts for repair were delivered quickly and they were easy to install. The Door Rack just snaps into place and the Drawer Support Rail only required tightening one screw after install. All the parts arrived in perfect condition and now my refrigerator is back to being as good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from AXSON, GA
- Parts Used:
- 240535101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My door rack broke
All you do is snap it on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from BACLIFF, TX
- Parts Used:
- 240358007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Simple
Took under 2 minutes to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Essington, PA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original shelf cracked and fell off. No glue or tape would hold.
Just snapped the item into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from MARYVILLE, MO
- Parts Used:
- 240337712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement door for the dairy compartment
It simply snapped into place. No tools required. A very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SENECA, SC
- Parts Used:
- 240530701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Matching up the mounting screw.
A single screw holds the part in place. The ONLY challenge is seating the new slide so that the screw hole in the glide matches the hole in the support assembly. Initially setting the glide into place mismatched by about 1/16 of an inch toward the back of the refrigerator. Firmly grasping the new part after mating it to the two receivers on the support assembly, pull it toward you until it clicks into place. The screw should mate cleanly to the new part without any difficulty. Make sure you get the right or left side part, as they are not interchangeable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FRANKENMUTH, MI
- Parts Used:
- 5304506469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Handle on Door
Followed instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nickalas A from CUYAHOGA FLS, OH
- Parts Used:
- 240530811
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
our meat drawer handle was broken
I just put the new one in with no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Taylor from Greenville, SC
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic support on rail had broken off
Easy peasy... took the shelf out of the fridge. Unscrewed the old rail. Screwed in the new one. Put the shelf back in. DONE!!!!
My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.
Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!
Thanks
My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.
Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marvin from MONTAGUE, MI
- Parts Used:
- 5304506469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
for some reason the handle broke where it is screwed on
only one way to do it
Was this instruction helpful to you?
Thank you for voting!