FFHT1725PS0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic drawer support had broken from extended use.
This was a truly easy snap-in repair. Because I live in a small fishing village on the coast of Venezuela, the only difficult part was waiting for the part to arrive. I'm very grateful that Part Select makes ordering parts easy and reliable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lancaster, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cheese drawer rail broke
I took out the screw and removed the old rail, then I used the same screw to install the new rail. It took me 2 to 3 minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Bellville, OH
- Parts Used:
- 240383901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken bin door on rental house refridgerator
the repair was simple but the real story was the easy to read blow up diagram of the refridgerator after I entered the model no. Everything was numbered and I new exactly what I was ordering.
I will definatley buy here again.
I will definatley buy here again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from Hamden, AL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Support rail for meat drawer broke
Super easy. We unscrewed the broken rail, and screwed the new rail into place. Much easier than expected!!! We were also pleasantly surprised to have the part arrive the day after we ordered it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from THIBODAUX, LA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drwr. suppt. broken-- cracked
took off bad part-- 1 screw-- took every bit of 3 min. to change
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James R. from Fayetteville, AR
- Parts Used:
- 240383901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf guard broken (the fastner)..
Open the door and slide on the part. No Tools required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from brighton, CO
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic drawer support had broken
I Removed the old broken piece and replaced it with the new drawer support, using the screwdriver it was a very simple operation.
Was this instruction helpful to you?
Thank you for voting!
Both support rails had broken
First, remove shelf unit from refrigerator and lay glass side down on a large flat surface. Observe, then pay attention to assembly. Spent more time with this, drinking coffee, and playing with puppy, than the actual repair. Only had to remove and replace two
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Center Point, IA
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Left rail was broken
The shelf needed to be removed from refrigerator and then remove the screw and pull the rail from the bracket on the opposite end. After installing the new rail it turned out to be a fraction of an inch too long so I had to file the cracket on the shelf which is metal. The rail slipped back in and was perfect. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorphial from Arcadia, FL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drawer Support Rail Left Side Broken
The Hardest Part Was Taking Everything Off The Shelf,Took Old Part Off And New Part Popped In And I Tightened The Screw And That's It Done!Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Jefferson, MD
- Parts Used:
- 215846604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer always has ice accumulating
Thermostat assembly, remove light bulb, remove 1 screw, drop thermostat casing, two screws to remove timer from inside and install in reverse. Old Timer had electric motor and lasted 30 years. New one looks to be electronic with plastic motor gears.
Was this instruction helpful to you?
Thank you for voting!