FFSS2314QE0 Frigidaire Refrigerator - Instructions

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

removed ice denspenser and replaced spring and flap'

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

it's very simple......take off the bottom plastic grate that catches the overspilled water, unscrew the 3 bottom screws, take off the black plate ( just lift up slightly), take out three more screws, then get the flashlight out. ......on top of the actuator, you will see 2 small silver-colored screws with very small silver-colored plates ( maybe 1/4 inch long), they hold the actuator into the unit. unscrew those and pull out the old actuator unit. You'll need to use your flashlight and pull the entire unit out to get access for replacment. Reverse the process for replacement, put in the actuator, screw in the 2 small silver-colored screws and there little plates, push the entire unti back into place, then screw in the remaining two sets of 3 screws......replace the faceplate and water grate and you're done.

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

It was as simple as removing two hex head screws to remove the old ice maker, then aligning the new ice maker (ensuring the downspout from the water supply was directed into the opening designated for it) and then screwing the two screws back into place. The most difficult part is the space that you have to work with. It was a little difficult and frustrating, but put in place, an hour later we had ice and it's worked great since!

just replaced old bins with new ones

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Old valve comes out with 2 screws, water lines removed and reinstalled on new valve just as they came off the old valve. Entire job took less than 10 minutes. Very easy replacement.

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)