FFSS2314QS0 Frigidaire Refrigerator - Instructions

I slid out the tray in the ice/water area and exposed the 3 screws to remove the unit/panel. I then had to unplug the electrical connection and work the panel around to where I could get to the 2 screws that hold the actuator in place. The water tube holds the panel tight making it difficult to access these two screws but I was able to complete the job in about 15 minutes.

Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!

Removed old broken pan cover and replaced with new pan cover..

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Put on new shelf in seconds. What a wonderful way to be able to purchase the perfect part easily through the internet. I ordered the part on Sunday and received it on Tuesday. THANK YOU Parts Select!!! K.F.

It was very easy to insert the new shelf door into the refrigerator slots.

Followed the online video from this site

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Easy

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

Unplug refrigerator first. Remove 4 screws on front and lift off cover. Unplug unit small plug with around 6 wire on it on the top. Unscrew inside scres that hold the lever in place. Put the new one in slots and put in screws to hold in slot. Put cover back on. Make sure ice dispenser is still working seemed to disengage the unit during the repairs.

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

This would have been an extremely easy job if the screws behind the catch pan hadn't been rusted.

After pulling the catch pan off, we had to cut a slit for a flathead screwdriver into the heads of the screws and only the middle one came out while the other two heads broke off.

There were two other places for screws (on either side of the middle screw )that weren't being used so when we put it back together we had to drill two holes through the panel that the screws were holding in place and find screws that would fit so we could use the middle screw hole and the two that hadn't previously been used so that when we put it back together it would have some stability.

Replacing the ice actuator was easy and putting it back together was easy.

The descriptions of other repairs for this part were dead-on accurate and very helpful.