FFSS2314QS8A Frigidaire Refrigerator - Instructions

Test the light socket first with a bulb that you know is good. If the light still does not come on, unplug the refrigerator, remove the switch by inserting a very small, thin, flathead screwdriver alongside it and pull the switch out slowly with your other hand. There are two wires there. Remove them gently with some needle nose pliers. If you want to test to see if the switch is defective, take a insulated jumper wire, and attach it between the two wires. Plug the refrigerator back in and see if the light comes on. If the light does come on, replace with a new switch by re-attaching the wires and placing it back in the hole firmly.

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

open refrigerator door unsnap & remove old bin. then just snap new bib in place. very simple.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector. This made it easy to replace and test, and then cut of the excess water line.
Thanks.

Pulled the old gasket off and put new gasket/seal on by pressing firmly into slot.

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

First of all, I ordered in the afternoon and the part was on my doorstep the very next day, amazing shipping. I shopped all over and this was the best price by a few dollars. I hope I never need any other parts, but if I do, I will come back to buy my parts here.

I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.

Followed the steps in the video on your site, really easy to do.

Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

While waiting for parts I removed the control and side panels, placed duct tape partly over the hole to the freezer to allow fridge cooling and left the panels lay inside plugged up while I monitored the fridge temp. This worked until the parts arrived.

1. Remove 3 hex screws holding (underneath) the front control panel
to the top of the fridge.
2. Remove 2 screws holding the left side assembly. The control panel
and the side assembly come down as 1 L shaped piece.
3. Unplug the large control cable and the small cable then remove
the entire assembly. Note the position of the freezer sensor
extending into the freezer. Separate the control panel from the
side assembly to access the cable bundle.
4. Remove and replace the Damper Control Assembly. Note: You can
remove the complete old styrofoam (glued in place) or cut the tape
holding a 2 part styrofoam section that holds the damper in place
and only replace the upper part. Be sure to tape the 2 styrofoam
parts back together. Make sure the freezer sensor is placed
properly on the Damper assy.
5. Remove and replace the old thermistor assembly, secure the wiring
bundle and reattach the control panel to the side panel.
6. Place the entire assembly back inside, plug up the cables.
7. While supporting both panels insert the freezer sensor in the
proper position and replace the 3 screws securing the control
panel then the 2 screws securing the side panel. Check that the
side panel is flush against the side after installation.
8 Wait about 12 hours for the temperature to stabilize.