FPHN2899LF7 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from LANCASTER, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
LEAKED WATER AFTER USING WATER DISPENSER
DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ELK GROVE, CA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
New off brand water filter could not be removed from the water filter base
Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Littleton, CO
- Parts Used:
- 241894223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
freezer section upper shelf slide assy broken, captive ball slides fell out
Remove frozen food and ice cubes to coolers so they stay frozen.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Remove shallow wire shelf.
Slide out both sides of slide assemblies. Defective slide unclip the front corner front frame remembering to remove the plastic retention rivet first. It has a centre pin that needs to be pulled out first. Support the rest of the frame on the bottom shelf/basket frame
There is one cap head square driver screw to remove on the wall of the freezer holding the slide in place. Leave the other two flat head screws alone. Slide the defective frame off the other two flat head screws. Take new part and attachment is the reverse of the disassembly you have just done. The front frame corner clip is a bit difficult to put together there is a top and bottom spring clip then the plastic "rivet" where you need to push in the centre pin to retain it in the joint. [a bit flimsy so be careful].
The shallow basket should be carefully placed on the front and side clips, and make sure everything is square. Then slide the shelf to make sure it goes into the freezer properly. Then you can re-load the food and ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from HENRICO, VA
- Parts Used:
- 242010901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Wrong Part sent!!!!!
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel.
I can't even find a return address to send it to.. Please help me
Elizabeth Romage
libbieinrichmond@comcast.net
8042627963
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John A from BRUNSWICK, GA
- Parts Used:
- 242252702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No water to ice maker
Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Oley, PA
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..
Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Brookfield, CT
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator wasn't staying cool enough
Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BOZEMAN, MT
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light Switch too loose so no longer triggered by the door.
Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORMOND BEACH, FL
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch not working properly
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Double springs, AL
- Parts Used:
- 242252702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Water was leaking from the old valve
Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike
Thanks for being there
Mike
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from OLATHE, KS
- Parts Used:
- 242009604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Was this instruction helpful to you?
Thank you for voting!