FPHI1888PF8 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JEFF from OLIVET, MI
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
FREEZER WAS COLD FRIDGE WARM
YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from Greensburg, PA
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom shelf on door cracked and broke
I ordered the Door Shelf Bin from PartSelect.com on Friday and received it on Saturday!! I was shocked, but thrilled. The easy to use diagram helped me to pick the right part and I easily replaced the broken one. I have already started to recommend PartSelect.com I was so thrilled with their service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from GILBERT, SC
- Parts Used:
- 242193206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Torn gasket
Replacing the gasket is easy, just remove the old gasket by pulling it out of its grove and push in the new gasket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- winifred from LOUISVILLE, KY
- Parts Used:
- 297286803
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Coming from the refrigerator, there was an intermittent "clicking noise", occurring about every 30 seconds. The frig. eventually failed .
I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Las Vegas, NV
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working
Took off old part and installed new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from SAVANNAH, GA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not running
After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from HENDERSONVLLE, NC
- Parts Used:
- 242077705, 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
EVAPORATOR FAN MOTOR & BLADE
The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from FORT WAYNE, IN
- Parts Used:
- 242193206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket was torn. The frig door not sealing properly
I peeled off the torn door gasket. Then installed new door gasket pushing and pinching it into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from georgetown, TN
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water Valve was leaking water and not making ice
I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from ORANGEBURG, SC
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
both bulbs blown out
unplug refrigerator and insert the bulb in refrigerator first and then insert the second bulb in freezer side. After which, plug the refrigerator back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MARTINEZ, CA
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Fridge made a hellacious noise and wasn't cooling well
From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.
After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.
I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.
I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.
After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.
I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.
I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from BUFFALO, NY
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped making ice and i knew it wasnt the mechanism since I could hear that working when I unplugged and plugged the unit back on.
I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up water but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from DANSVILLE, NY
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Fridh light bulb blew
Got sent the wrong bulb 3 times had to pay for the three bulbs 75 dollars each Sent pictures of right bulb still wrong bulb no refunds for 30 days I even gave them right part number. Found out that the part number on box but wrong bulb inside told them and they seem not to care ordered from another company still out 225 dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie L from Eureka, CA
- Parts Used:
- 240338101
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken Plastic Edge
Easy peasey just slipped it in
Was this instruction helpful to you?
Thank you for voting!