LFHT1817LF9 Frigidaire Refrigerator - Instructions

Pulled the drawer out, lifted the shelf out of the refrigerator, unscrewed drawer slides from shelf and rescrewed the new drawer slides and returned the shelf, drawer, and the job was finished. Thank you so very much for your speedy delivery.

Very simple. Remove the 2 top screws on the door, slide the lower part of the handel on to the lower screw on door .,swing the handle up to the top of he door and attach with the 2 original screws. DONE

I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.

Easy replacement, I did add some glue to improve hold. The new handle design was a little different and did not match freezer door so I had to change both. I guess that's why they sell as pair.

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

Unscrewed the screw. Replaced the handle, with new handle, rescrewed screw.. easy peasy! Perfect fit part

It was easy to remove the broken handle and install the new on. Only thing needed was a screw driver.

Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.

I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl

Simple repair and less than 30 minutes.
But the video you had was taken down which showed you need to wind the timer. I called and was promptly sent another video, thanks Ashley !

Unfortunately the second video did not mention that you have to wind the timer, like the first video did. Turn clockwise till you hear 2 clicks.

All good. 20 year old fridge chugging along.

I simply loosened the screws holding the refrigerator door handle and then slid the bottom portion of the handle off from the screw holding it in place. The bottom portion of the handle did not exactly marry-up with door, showing a very small gap. I attributed this to the age of the appliance.

Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.

Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

Removed the old handle by taking the screw out at the top and sliding the bottom part off. Then slid the new handle on at the bottom replaced the screw at the top and done. Took less than 2minutes from opening the package to done.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.