FPUS2698LF3 Frigidaire Refrigerator - Instructions

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

Twisted replacement bulb into place easily. Let there be light!

Slid the meat pan out of the fridge, popped the glass from under and removed it, popped the front of shelf upward and then slid it out, and for the new one I did everything in reverse that’s it took me less than 10 minuets.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

Well I’ve been cleaning refrigerators for 50 years... so have experience removing shelves etc., for cleaning....I removed shelf and then glass and put new one in........easy peasy

Removed the previous water filter. Installed the new water filter.
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.

Time to install, less than 8 minutes.

Thank you Parts Select!

I ordered a new shelf and I put in, less than minute

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.

This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.