FPHB2899PF6A Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andres from Golden Valley, MN
- Parts Used:
- 241778315
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced door gaskets with new ones
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul S Van from BRUNSWICK, ME
- Parts Used:
- 242194301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Trim on door water/ice dispenser broke off
Removed two screws and disposed of two broken tabs holding old trim in place. Placed new trim in place, fastened the same two screws. Done.
About two minutes.
About two minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lancaster, SC
- Parts Used:
- 241778315
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GASKET WORN AND LEAKING
SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND
THEN PUSHING THE NEW GASKET BY HAND
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hampton, NH
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
Previous seal had a tear and cold air was leaking around seal
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from SAN ANTONIO, TX
- Parts Used:
- 243297613
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
There is no power, due to the COVID-19 pandemic there no Tech support available,
My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from MAGNOLIA, AR
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
ice maker is stuck on crushed ice.
We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lexington, SC
- Parts Used:
- 5304537408
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from Austin, TX
- Parts Used:
- EAFCBF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
routine maintenance
slide old filter out and insert new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from OLATHE, KS
- Parts Used:
- 242009604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Filter wouldn't engage
Basically unhooked water lines and removed the screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Pawleys island, SC
- Parts Used:
- 242253002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Refrigerator water dusoeswr stopped working
I removed the defective water valve. All wiring and tubing connectios were color coded.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
It connected the water tubes and electric plugs to new water valve.
The water dispenser worked perfectly after I reconnected everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ASBURY PARK, NJ
- Parts Used:
- 5303918493
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Easy peasy.
Easy repair. Great part. The hardest part was removing the fridge lower exterior door so I could get access to the icemaker. A couple of youtube videos later I realized loosen a screw, slide the icemaker out and unplug slide the new icemaker in and plug-in making sure the water spout was accurately over the water receptacle for the icemaker. Several hours later I was up to my eyeballs in beautiful clear ice cubes. Highly recommend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Warrensburg, MO
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
time to change water filter
first, there many different water filters. your experience will be different according to your water filter type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from CIRCLEVILLE, OH
- Parts Used:
- 241778811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flipper mullion assembly broke
Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from Riverdale, NY
- Parts Used:
- 242037202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Our older bin shelf was cracked
Simply removed old shelf and installed new one.
Was this instruction helpful to you?
Thank you for voting!