FPSC2277RF1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from NASHVILLE, TN
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Valve body separated : major leak.
Write down where tubing goes, wiring is color coded.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from FREE SOIL, MI
- Parts Used:
- 243297613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Original ice maker not working leaking water water out door
Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Pittsburg, PA
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Leaking Water Vlave
Just follow the instruction that come with the valve. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAVAUGHN from MIAMI, FL
- Parts Used:
- 5304512686
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Installed new inverter
Secured bracket. Attached electrical contact to the compressor. Secured inverter to bracket.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from CYPRESS, TX
- Parts Used:
- 240599301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked frame
Found model
Checked website for part availability
Ordered
Tracked package
Received
Removed old
Placed glass in frame
Placed on rack in fridge
Replaced crisper !!
Checked website for part availability
Ordered
Tracked package
Received
Removed old
Placed glass in frame
Placed on rack in fridge
Replaced crisper !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from BIG SKY, MT
- Parts Used:
- 240599301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke one of the support wheels out of its seat. It supports the left crisper.
Tried JB Weld, not sufficient.
Got online, looked at the parts fiche for my model, chose the crisper top frame. Wrong part. Sent it back (shipping as $60 on a $125 part).
Ordered the part that the wheel appears to be screwed into (described as crisper support frame. Ordered new $11 plastic wheel as well.
Wrong part. It appears that the crisper drawers on my unit are supported by a monolithic piece (solid plastic) that includes the frame as well as the locators for the wheels. I could send pictures, but have decided to abandon fixing it. (I tossed the metal support that was the second order into the trash ($60 part)....
Got online, looked at the parts fiche for my model, chose the crisper top frame. Wrong part. Sent it back (shipping as $60 on a $125 part).
Ordered the part that the wheel appears to be screwed into (described as crisper support frame. Ordered new $11 plastic wheel as well.
Wrong part. It appears that the crisper drawers on my unit are supported by a monolithic piece (solid plastic) that includes the frame as well as the locators for the wheels. I could send pictures, but have decided to abandon fixing it. (I tossed the metal support that was the second order into the trash ($60 part)....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Sapulpa, OK
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Water began to leak from valve
We followed the online instructions and tah-dah it was working...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Jensen Beach, FL
- Parts Used:
- 241993101
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water dispenser dripping causing corrosion below tray
Replacement of the water valve repair was a snap. Only the main supply line needed to use a nut to secure the water supply. All other lines were simply cut below the pointed end of the plastic tubing line, nylon nut discarded and simply pushed in to seat with a O-ring fitting. Took no more than 10 minutes to install the new valve and test for leaks after turning water back on. This was the easiest appliance repair I have done in > 5 years, 100% success first time,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from bellmawr, NJ
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken support
had to remove broken by pushing 1pin then remove.
put new one in reset pin done.
put new one in reset pin done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Fort Wayne, IN
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken crisper supports
The video was very helpfull. They were fixing the same refrigerator that I have. I punched in the set pin on the old part. Removed the old part by prying it out with a putty knife. Inserted the new part and drove in the set pin. I was glad that PartSelect had my parts. The repair shop in Fort Wayne Indiana did not even show this repair part on their computer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvin from Barbourville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
left out in the cold an froze
remove the old one and replace with the new one and yes it was that easy. All of the lines and wiring connectors were color coded
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Lakeland, FL
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass Shelf Insert shattered in my hand while I had it out cleaning it.
Simply replaced the glass shelf. Fit was finish were great.
Was this instruction helpful to you?
Thank you for voting!