FFTR21D2PS3 Frigidaire Refrigerator - Instructions

First download schematic from frigidaire.com and watch a few youtube videos on fixing refrigerators .At first my guess was the timer was stuck on the defrost mode .However after studying the schematic I checked to see if the power was being sent to the compressor through the starter ptc .The 110 v was there after pulling off the connector .Also the condenser fan was on confirming this . however the compressor was stone cold .the compressor has 3 inputs whose resistances across all seemed good (see youtube videos) so it was probably the ptc starter or the 15microfarad capacitor .I changed the capacitor first -not the problem .then the ptc starter .immediatey the compressor started warming and after a few minutes cold air was being blown in .Very satisfying !

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Opened the box, took part to refridgerator and inserted retainer bar in place.

snaped right in.

I took out the plate that covers the evaporator in the freezer with 3/8 nut driver. I removed the clips holding on the fan cover and used the pliers to take the fan off the old motor. I then took the old motor out, affixed the fan to the new motor and replaced the motor and fan assembly. I reassembled the entire fan assembly and reinstalled the evaporator plate

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The retainer bar was so easy I installed it in less than 5 minutes.
I highly recommend Part Select service including, ordering, their knowledge and expertise of their products.

Discovered the coil was covered with 1/2 inch of ice because defrost cycle had not been working. Replacing the defrost timer and melting ice with hair dryer fixed problem. Hooray!

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Easiest way to install was to insert the cover first then insert the glass insert being sure to tilt a little and inert under the shallow lip at the front of the cover. Not a good idea to assemble before inserting in the fridge. When cleaning the refrigerator shelves in the past I took then out of the refrigerator, cleaned them and re-installed in the method above. Just was not careful enough removing when I dropped the glass

I broke the glass shelf in my refrigerator. I had trouble navigating the website, so I called the customer service line, and the lady was lovely to speak with, and ordered my part quickly! In 2 days I had the part, and it fit perfectly!

Great service, great price!
Thank you!

I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task

The repair was quick and easy. I simply removed the old/cracked door shelf retainer bars and snapped the new ones into place.

No tools needed. Popped out old gasket, cleaned/sanitizeddoor and popped new gasket into grooves. Door now closes tightly!!!

Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.