FGHS2655PF5A Frigidaire Refrigerator - Instructions

Removed all contents from the glass shelf.
Lifted out the glass shelf.
Lifted out the broken plastic frame.
Set the new plastic glass shelf frame in place,
Washed the glass shelf.
Placed the clean glass shelf upon the new frame.
Replaced the removed contents onto the glass shelf.
Fini!!!

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

I followed the video tutorial published here. The step I altered was setting the shrink wrap; I did not have a heat gun to safely shrink it, so I folded it tightly onto itself and wrapped it in electrical tape. No more frost buildup.

This is the second time I've had to replace the crisper cover, so I had that step mastered. As before, I took the glass from broken crisper cover and dropped it into new cover in seconds. Had to use a screwdriver to pry old crisper supports from the walls of the fridge. This was the only hassle. Popped new supports in, replaced crisper covers, and slid crisper drawers back into place. From now on, I'll have to be more careful about how much weight I put into crispers.

Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...

Went to oartselect.com located diagram and part. Took out ice drawer to prevent ice being dispensed. Remove small front panel in door for ice- water & cubes, 2 square tip screws on top. Remove small grey panel, 2 Philips head screws, remove ice dispenser unit 2 Philips screws, unplug 1 wire connector.
Insert ice dispenser unit from partselect.com, connect wire connector, screw in 2 Philips head screws, place cover panel in position and screw in 2 Philips head screws, place small grey panel in position and screw in 2 square tip screws. Put ice drawer tray back in refrigerator, try water, try crushed ice, try cubes. FINISHED, just saved yourself a couple of hundred dollars in less than an hour. My wife said she could do it after watching how easy it was.

Slid the meat pan out of the fridge, popped the glass from under and removed it, popped the front of shelf upward and then slid it out, and for the new one I did everything in reverse that’s it took me less than 10 minuets.

The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

I ordered a new shelf and I put in, less than minute

Well I’ve been cleaning refrigerators for 50 years... so have experience removing shelves etc., for cleaning....I removed shelf and then glass and put new one in........easy peasy

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.

We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....