FGHS2655PF6B Frigidaire Refrigerator - Instructions

Had to remove the refrigerated items off the crisper shelf to remove the glass, next removed the drawer to remove the crisper frame, then removed the middle drawer glass to remove the drawer, then the frame, installed the new frame cleaned the glass, re-installed the middle drawer, and continued the installation steps reverse of the removal process.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

Replaced the Triple Water Valve

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

Followed instructions for this part from this site and things went well.

I first opened the breaker controlling the outlets by the refrigerator. After verifying there was no power to the refrigerator, I removed the screws holding the trim façade in place and removed it. Next I removed the screws holding the control board in place and removed it from its position and then disconnected the wires connecting it to the ice dispenser module. I then used the diagonal cutters to cut the flex-tie holding the water inlet tube in place. Next I removed the screws holding the ice dispenser module in place and unclipped the water inlet tube from it and removed the whole unit. I then attached the water inlet to the new dispenser, flex-tied it in place and reversed the above stated process. Once completed, I restored power and everything worked well.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

I ordered 3 bins initially and received only one, which was very easy to install. It just snaps in. When I called to indicate that I had received only one of the 3 bins, a claim was submitted and I got a refund for the missing parts. Then I had to reorder the two missing parts.

When I received the reorder, both of the bins were broken. I called to indicate that they were broken. I was told that I would have to submit photos of the broken parts to photos@replaceparts.com, which I did. After I submitted the photos, I received an email asking me for the photos again and the serial number of the refrigerator. This is the first time the serial number was requested. I have no idea why they wanted the serial number at this point instead of when I first ordered the parts.

At this point, I am still waiting to get my claim for the broken parts approved. I assume that the shipping department is pretty worthless, since they screwed up my order to begin with and then the shabby packing that was done for such fragile plastic parts on the reorder.

I'm not happy with the hassle that I have been going through just to get a simple order delivered.

Slip out old shelf, remove glass and clean, slip in the new shelf and replace glass on top. That easy

Glue the old one with gorilla glue. Made space and put the bin in. Now I have an extra one.

Easy. Just placed the bin in position.

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.