FGHT1844KR8 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dianna from HALE, MO
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My Crisper cover was cracked and broken.
I ordered the replacement part. Cleaned out the bottom of my refrigerator, popped in the new part, replaced the food and was siting in my recliner in under 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from WELLS, ME
- Parts Used:
- 5303918202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Refrigerator and freezer running to warm.
I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Callie J. from YORKTOWN, VA
- Parts Used:
- 5304511738
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer light bulb went out.
Used my hand to unscrew light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from DUMAS, TX
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
Real easy took out the broken ones and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DAYTON, OH
- Parts Used:
- 240337103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front upper edge of crisperpan was broken
Slid out old, broken pan and slid in new replacement pan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Catskill, NY
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door shelf broke.
Very easily did the repair -- popped the new door shelf right in the place of the old one! No tools needed, no hardware, easy! The part actually measured 24 3/4 but the replacement part said "26 inches" on website & this was THE replacement part. Put this off for so long--ordered part and recd within 2 days, great!
Was this instruction helpful to you?
Thank you for voting!
Bin door has never been secure. It falls off every time we open the door.
Did nothing. The old bin had been repaired so many times just trying to make it stay in place that we threw the old one away and bought a new one. While at it, I looked to see if I had room for another shelf bin. I simply snapped it on too. The new door bin that I purchased does not stay on any better than the one I replaced. My summation would be that the little clips that protrude to hold it on are either too rounded and it slips off or they are simply not long enough. One bump and this bin is in the floor along with it's contents.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Cleveland Heights, OH
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace shelf
I can't believe I put if off so long... so easy to do and PartSelect was very fast, efficient, and the cheapest vendor for my part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from PRINCETON, IN
- Parts Used:
- 240338201
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The refrigerator we purchased along with our new house had a broken door bin.
We found the model number and looked online and found this site. The diagrams they provided was very helpful in finding the bin we needed. When the bin arrived it was exactly what we needed. Thank you for your excellent service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arsen from Glendale, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
i smell very bad smell coming from refrigerator
I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!