FGHT1848PF3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HELENA, AL
- Parts Used:
- 218906802
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Getting the light socket to snap back in properly
It snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Green Bay, WI
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken clip on the shelf on the bottom of the door
I watched the short repair video that was provided for the do it yourself persons.And I put the new shelf in place in the door myself it was fast and easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from arlington, WA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
has lights,no fan or compressor
jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Jefferson, MD
- Parts Used:
- 215846604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer always has ice accumulating
Thermostat assembly, remove light bulb, remove 1 screw, drop thermostat casing, two screws to remove timer from inside and install in reverse. Old Timer had electric motor and lasted 30 years. New one looks to be electronic with plastic motor gears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph f from Boscawen, NH
- Parts Used:
- 240338313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bathroom door
Just took old knob out put new knob in real easy thank you jd
Was this instruction helpful to you?
Thank you for voting!
My Frig Light Stopped
I am a 65 year old woman with no mechanical aptitude: I just unplugged the frig. And used a screw driver to pry of the plastic socket from its outside edge. . Then you just unplug two tiny contact plugs that appear when you pull out the socket and replug in those two the same way on the new part. Pop the socket back into the hole . . . . And screw in the new bulb. I knew I needed the socket part cause when the bulb burned out , a new bulb still did not work. . . If I can do it, anyone can!
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door sagged, had to push the door to close it.
Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bethel Park, PA
- Parts Used:
- 240350608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass shel
After removing the broken glass, the new shelf slid into place easily. I only had to make sure it rested in the front slot that prevents it from sliding. The ordered shelf arrived within 4 business days and was perfect in all ways.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- antonina from woodbridge, VA
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the door shelf bin broke
just put in the shelf in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernia from Maywood, IL
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf door broken apart in the middle
Removed the old door (squeeze a little at the ends), Took the new part out the box, and snapped it on. Too easy! This is my 2nd time ordering a shelf door from Parts Select and both have been great experiences! They are super fast, reasonably priced and the instructions/locating the part process is really easy and thorough! I can extend my appliance life a little longer with Parts Select. Thank you so much as this is a money saver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from West Sayville, NY
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom shelf bin that attaches to the refridgerator door was cracked
The schematics on the website allowed me to pick the exact part I needed. The repair was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe N from Alliance, NE
- Parts Used:
- 240350608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper's Glass Top Broken
Placed glass into front edge of frame first then gently lower the back side down into position
Was this instruction helpful to you?
Thank you for voting!