FGEX26D6QF0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary A from SEMINOLE, FL
- Parts Used:
- 242270107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker dispenser in door would not shut off
Went to oartselect.com located diagram and part. Took out ice drawer to prevent ice being dispensed. Remove small front panel in door for ice- water & cubes, 2 square tip screws on top. Remove small grey panel, 2 Philips head screws, remove ice dispenser unit 2 Philips screws, unplug 1 wire connector.
Insert ice dispenser unit from partselect.com, connect wire connector, screw in 2 Philips head screws, place cover panel in position and screw in 2 Philips head screws, place small grey panel in position and screw in 2 square tip screws. Put ice drawer tray back in refrigerator, try water, try crushed ice, try cubes. FINISHED, just saved yourself a couple of hundred dollars in less than an hour. My wife said she could do it after watching how easy it was.
Insert ice dispenser unit from partselect.com, connect wire connector, screw in 2 Philips head screws, place cover panel in position and screw in 2 Philips head screws, place small grey panel in position and screw in 2 square tip screws. Put ice drawer tray back in refrigerator, try water, try crushed ice, try cubes. FINISHED, just saved yourself a couple of hundred dollars in less than an hour. My wife said she could do it after watching how easy it was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B J from Dillingham, AK
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frost build up on evaporator
Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SYLVANIA, OH
- Parts Used:
- 240597220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
2 drawer undercounter beverage ref not getting cold enough. Wont get below 48°
Took drawers out by removing 2 screws on top of rail near front, then popped black plastic cover off in lower right inside cabinet...sensor just un plugged and new one plugged in easily...did not fix problem though...display set at 34 but bottom drawer reads about 40 at best and upper drawer reads around 55...dont think the 3 little fans inside on back wall have been running
Was this instruction helpful to you?
Thank you for voting!
3 door bins got broken
I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from lincoln, NE
- Parts Used:
- 5303918344
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker quit working & was over flowing
We had to unhook & remove icemaker several times, thaw it out & reinstall, it would work for a day or two then overflow. Bought the new ice marker, replace it and it works great....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Huntersville, NC
- Parts Used:
- 240356402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I dropped and cracked the door bin
2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from PHILADELPHIA, PA
- Parts Used:
- 240350649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I took the shelf out to wash it and it broke in a million pieces
I ordered a new shelf and I put in, less than minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaylan from ALEDO, TX
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced the water filter
Removed the previous water filter. Installed the new water filter.
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.
Time to install, less than 8 minutes.
Thank you Parts Select!
I then filled a large glass full of water from the water dispenser several times to clear the air from the filter and lines.
Time to install, less than 8 minutes.
Thank you Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roxie from PORT ST LUCIE, FL
- Parts Used:
- 241969501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
plastic frame broke in front needed replaced
Well I’ve been cleaning refrigerators for 50 years... so have experience removing shelves etc., for cleaning....I removed shelf and then glass and put new one in........easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Hot Springs Village, AR
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
When washing the shelf insert glass piece, it broke into a million pieces.
The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Greensburg, PA
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice tray wouldent fill.
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Ocala, FL
- Parts Used:
- 240334201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One arm on the plastic bin or tray cracked and broke.
This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Denver, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water dripped from water outlet on door
Replaced the Triple Water Valve
Was this instruction helpful to you?
Thank you for voting!
chrisper drawer jammed found supports were broken
Looked at video on how to remove and reinstall support and followed the instruct ions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from PHILADELPHIA, PA
- Parts Used:
- 240599301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The top crisper drawer frame was cracked, it secures the glass top also.
Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.
Was this instruction helpful to you?
Thank you for voting!