FFTR1514QWDA Frigidaire Refrigerator - Instructions

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

remove screws at top of lower door, replaced with new handle very easy to do.

The lower attachment of the handle needs to be put on first with the top of the handle pointing to the left of the door. Then the top part can be swung in place and screwed on easily

Open refrigerator door to gain access to top door handle mounting screws. Remove two screws at top of the handle on the refrigerator door. Slide handle up to release the bottom mount. The handle is now removed. The bottom screw remains in the door. To install the handle slide the mount onto the bottom screw and check the fit. If the fit is loose screw it in clockwise and check the fit again. Adjust the screw until the bottom fits flush with the door face. Align the top two mounting screws and snug them up. Close the door and align the bottom handle with the top handle. Open the door and do a final tighten on the top two screws. Be careful not to over tighten because you can crack it.

took the cover off
(cardbord) the fan will come off and go back on by hand no tools needed i changed the fan motor just to be sure. 3 little screws hold it on. the plug only goes on one way u can't mess it up.very easy job u shouldn't have any problems doing it.Jim

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

I popped the new one in. My cat could have done it

Removed screws. Rotate door handle, and slide it off anchor screw. Slide new door handle on anchor screw, and rotate door handle into position. Replace screws.

All I did was to take out the cracked pan and slide in the new one.Excellent service.I ordered the pan late evening one day the part arrrived not the next day but the day after.I expected that it would have taken a week or better.I recommend Part Select.com because of this.

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

I snapped the parts into place. The fact that the parts I recieved were original parts from Frigidaire made all the difference. I feel if the parts had been after market parts they would not have fit so well.

Took old handle off . Then slipped new one on bottem in place @ top placed screws in place .Very easy .

I’m a technician,I was contacted by a customer. After listening to the customers issue I determine the freezer evaporator fan was bad. Real easy job loosen the hex head screws on top of the ice maker and pull it straight up. Disconnect ice maker wiring harness.remove the two top 1/4” screws that hold the back cover on and pull it forward. Disconnect your wiring harness and remove the whole back panel. Lay the back panel face down on the floor and remove two metal clips that are up at the top with a flat head screwdriver. Center plastic panel slides up and out maybe necessary to take a flat head screwdriver to the very top to release the plastic clip. Pull your fan blade off. On the backside of the motor just take and twist the flat plastic piece counterclockwise and remove your motor and install the new one Reassemble in the opposite order.

After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.