FFTR1614RW1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duarte from SEDRO WOOLLEY, WA
- Parts Used:
- 242077705
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
the refrigerator stop making ice and only the bottom part was cooling
first i order a defrost termostate i replace it but wasnt the problem then i
unpluged the evaporator fan motor and test it and was not working order
a new one and working like new.
unpluged the evaporator fan motor and test it and was not working order
a new one and working like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amit from Glendale, CA
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Handle borke into 2 piece
As I was aware hot install it, bec a couple of days back, the handle pop out of the lower screw shaft. The easy steps is put the lower part first, keep the handle diagonal to the door, once the lower screw is fit into the shaft, turn it to right to place the holes on the door holes and just jack in the screw.
Its pretty easy.
Its pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from VILLE PLATTE, LA
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door handles on both frig and freezer in rental house.
simply backed out 2 screws on each of the handles, then by observing the key ways in the new handles, i realized all i had to do was push down on the old handles to release them. then it was a snap to slip the new handles in and secure them with the original screws. SO EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from Wellington, KS
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rental house, fridge door handle broke off and renters threw it away.
Ordered the handle from Part Select, waited a couple days and it came in the mail. Husband took it to the rental and replaced the handle. Very easy process from beginning to end. Have put Part Select in our favorites to keep. Thank you so much for this service and the ease of the process.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door sagged, had to push the door to close it.
Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Gambier, OH
- Parts Used:
- 241559801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light socket burned out
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nick from montevideo, MN
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken, unrepairable fridge door handle
removed broken installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from arlington, WA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
has lights,no fan or compressor
jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Sarver, PA
- Parts Used:
- 240313703
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernestyna from Clearwater, FL
- Parts Used:
- 218428101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
both door handles broke at different times
It was a-b but they did not send any screws. So make sure you save your screws.... I was very very amazed how fast the shipping was. very very fast.
Was this instruction helpful to you?
Thank you for voting!