FFHT2116LK2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from TALLAHASSEE, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawaer support on right side of top shelf broke
Unscrewed screw from back of shelf pulled broken part out of slot it holds in and replaced with new one screwed the piece back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Mansfield, OH
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace meat drawer support
Removed glass shelf and frame. Unscrewed support from frame,replace with new support and screwed it into the frame, attach drawer and replace shelf in fridge .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from YOUNGSTOWN, OH
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator did not cycle
Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?
Now what?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VIRGINIA BCH, VA
- Parts Used:
- 241554901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door switch was no longer making my light go on when door opened
I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Pottsville, PA
- Parts Used:
- 240337712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Dairy door was cracked by an item in the refrigerator and broke into two pieces
This was not technical at all. The old door fell out and the replacement door snapped right into position. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janette St from KALISPELL, MT
- Parts Used:
- 240534701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Had a broken part in the door that holds condiments in
Removed broken part and then snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from FLOURTOWN, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken
Simple replacement. One screw to be tightened
Was this instruction helpful to you?
Thank you for voting!
2 shelves were broken and missingg
I (female) fixed it by just inserting the brackets. Easy as pie. I was so happy that they fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from CINCINNATI, OH
- Parts Used:
- 5304506471
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle again.
Install the new handle was very easy. These handles are no doubt made very cheap since this is the 3rd one I replaced in 15 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from MARKLEYSBURG, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The slide rail(Drawer Support Rail) I found was made very cheaply. None the less I had to replace it. I did watch the Repair tutorial on your site that made the repair a snap. Ezpeeze!
Removed the shelf and one screw on the back of the rail. Replaced rail and screw. Re-inserted the drawer and it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from rohnert park, CA
- Parts Used:
- 240530701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
support rail broke
removed top shelf from refrigerator, and placed it upside down on counter. removed 1 screw from old track and track was out. put new track in place, put in screw and replaced shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!