FFTR1814LBN Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carol from ROCKVILLE, IN
- Parts Used:
- 240337103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidently dropped the crisper drawer and it broke on the left front corner.
We received the crisper drawer in magnificent time and unpacked it and washed it and dryed it, and just slid it into the refrigerator. Thank you for your very prompt service.!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from BASKING RIDGE, NJ
- Parts Used:
- 215846604
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Refrigerator had not been cooling
Discovered the coil was covered with 1/2 inch of ice because defrost cycle had not been working. Replacing the defrost timer and melting ice with hair dryer fixed problem. Hooray!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from SUNDANCE, WY
- Parts Used:
- 5303918774
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
fan motor quit working
A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from WHITEHALL, NY
- Parts Used:
- 240524102
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken fan blade
I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlene from DOERUN, GA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke glass on crisper
Just slide glass in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DAYTON, OH
- Parts Used:
- 240337103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Front upper edge of crisperpan was broken
Slid out old, broken pan and slid in new replacement pan.
Was this instruction helpful to you?
Thank you for voting!
The door shelf retainer bars cracked.
The repair was quick and easy. I simply removed the old/cracked door shelf retainer bars and snapped the new ones into place.
Was this instruction helpful to you?
Thank you for voting!
Had to replace broken crisper shelf frame & broken door shelves
Removed broken parts and snapped in new parts No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from BAY CITY, MI
- Parts Used:
- 5304506471
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door handle broke off
used Phillips screw driver to remove two screws form the top off old handle on top of lower door. slipped new handle on the stud and installed screws in the top of handle .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from DUMAS, TX
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None
Real easy took out the broken ones and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lancaster, CA
- Parts Used:
- 240313703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The original part was plastic/and broke
unscrewed to little bolts and installed the new/metal part we got rfom partselect.If we may say.this is a great company to buy from! Fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from Jersey City, NJ
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
The refrigerator door did not come for the opening swing to be reversed
I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!