FGUN2642LP8 Frigidaire Refrigerator - Instructions

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

The new inlet valve came with pisco connectors so had to cut the end of the tubes off. Before doing this I marked all the tubes to make sure they were replaced in the correct order. The pisco connectors are great to use and very quick. The total install time was about 20 to 30 minutes. While you have the back of the frig off make sure you vaccuum the fan and coils. It was making ice in less than 20 minutes.

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

problem still persists part did not fix problem. made repairs recommended per your site.

Once the filter arrived, I pushed it in that releases a latch and removed the clogged filter. I then pushed in the new filter and when it clicked, I ran a few cups of water through it to clear any debris left from manufacturing and the job was finished. Less than 15 minutes.

Lifted off the bad shelf and installed the new shelf. Works great just like new again.

Removed new replacement crisper from packaging. Washed crisper in warm soapy water. Rinsed & dried crisper. Aligned crisper drawer with tracks on crisper shelf and slid crisper in until front panel was in home position. Slid crisper full travel in & out a couple of times to check not only for correct travel but also travel stops. Adjusted crisper setting, placed produce into crisper, closed crisper, & closed refrigerator. WARNING do not slam, drop, or otherwise mishandle crisper. It's only plastic!

Push in on filter and it releases pull filter out. Slide new one in push in and it locks it. Run water for 2 minutes and it is finished

it is a very simple process. pull out the water filter. put in the new one after removing the plastic tops. slide the filter in place pushing to set it in place. run water through water spout on door of fridge for about 3 minutes or until all the air bubbles are out. and there you are ready for a drink of water.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

Pulled out the fridge from the wall, unplugged it, and turned off the water supply. Took off the cardboard backing at the bottom of the fridge. Cleaned the dust and gunk. Unscrewed the old valve. Unplugged the 3 electrical connections. Since the new fittings for the water lines were different, we unscrewed the old ones, lopped off the nipples, and inserted the ends of the water lines into the new connections (they were super easy - just push the line in until it clicks). Reattached the valve. Reattached the cardboard. Turned water back on, and plugged in the fridge. Our ice maker still didn't make cubes, though. So I took out the fill valve from the top rear of the fridge. It had a tiny piece of ice lodged in the bend of the back, right above where it connected to the water line. I rinsed it out, reinstalled, and now we have a full bucket of ice!!