OEMF3-FRS26ZXHD2 Frigidaire Refrigerator - Instructions

Unloaded the drawer, pulled it out, took off the front panel, put the panel in the new drawer, reloaded the drawer, and put it back into the fridge.
I had the new drawer back in the fridge before the wife even knew I had taken it out of the box. I have been banished from storing my beer in the bottom drawer sincs I broke the old one. This should be the last drawer repair that I have to make.

Pulled the upper drawer out, slid the faceplate/handle up and out of the channel in the drawer. Took the new drawer and slid the faceplate/handle down into the channels and it was done.

Twisted replacement bulb into place easily. Let there be light!

Used pliers to remove filter.

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Ordered gasket and gasket arrived within 48 hrs. Put the unit into out-of-commission status. Defrosted cooling coils. Dried the coils thoroughly. Reinstalled cover panel to the coils. Removed existing door gaskets. Installed new (2) gaskets. So far ice buildup to the coils had ceased.

I started by shutting off water supply and unplugged refrigerator. Then using a nutdriver removed back lower panel exposing the dual inlet water valve on the left side which was held in place with one bolt. After unbolting the valve you can pull the entire assembly out enough to remove the three water connections. The instructions suggest cutting of about 1/2" off of the two discharge lines to provide a better connection to the new valve. The entire process was very simple. The price of the part was a small fraction of the new refrigerator my wife was threatening to buy if I did not get her ice maker working again. Thanks for another great repair experience!

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

I followed all the usual suggestions about changing the water filter and disconnecting the exterior copper line and testing it to make sure flow was steady. I then got ambitious and diconnected and tested the flow of water through each of the refrigerator's interior valves. Isolating my problem inside the dual valve that regulates feed into the water dispenser and icemaker I was able to clear out the blockage with a small dustbuster air cannister but reassmbling the valves somehow caused the valve to no longer function right so I ordered a replacement valve and had it all reconnected in five minutes once the part arrived. A simple repair to avoid a very costly replacement! Partselect has now been used by me to repair my oven, refrigerator (twice) and microwave. A pretty good alternative to replacing an appliance if you are willing to try your own repair.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

All I had to do was place the two new shelves in the desired locations.

The longest part of replacing the drawer was swapping all the veggies out of the old one. No tools,slid the glass drawer front from the old one and slid it into the new one.

I first replaced the defrost timer about a week prior and it did not correct the problem. I then ordered the thermostat from partselect and within 15 minutes had the part installed. My refridgerator has been running correctly for a couple weeks.