FRT21BH8CS1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Adam from BERKSHIRE, NY
- Parts Used:
- 5303918549
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, no fridge
Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginald from WEST PALM BCH, FL
- Parts Used:
- 5303918549
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Noise from fan
I watch the video on your site and this make iit very easy to do. That repair that tooks me 40 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
Drawer rails wore out for the meat drawer
Took off worn out rails and replaced with new ones using a Phillips screwdriver.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from LAGO VISTA, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner broken
Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earnest from BOWDON, GA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Gasket was damaged everything inside would freeze
Pulled the old gasket out and pushed the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TUCSON, AZ
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light not turning on when door opened
Used a flat head screwdriver to pop out the old switch, removed the contacts and placed on the new switch, popped the switch back in. Done in about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ROANOKE, VA
- Parts Used:
- 240356501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rail was broken
After removing meat tray the entire shelf including rails needs to come out. Once out a single set screw in the middle of rail needs to be removed. You can then slide the old rail across and then pull it out. Then insert new rail, slide across to lock in place. reinsert set screw. Don't over tighten. Be careful when replacing shelf as left side has air opening for drawer that must to match up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PHILADELPHIA, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHERRY from LAUREL, DE
- Parts Used:
- 241872512
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No problem
It was so easy to install it. I did great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Hayes, VA
- Parts Used:
- 241872512
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket failed
Simple. Just pull old gasket free from door. Pace new gasket on door and ensure that gasket is seated in the gasket channel all the way around door. This part fit door properly.
Was this instruction helpful to you?
Thank you for voting!