MRS22HNCD0 Frigidaire Refrigerator - Instructions

Got the new one and took the face plate off the old and sliped it right on to the new one. I noticed that the guide edges on the new Drawer are made better. That is added bennie.

Thank you so much

First we took the the old drawer out and pride off the front clear covering on both sides. Then we placed the front covering on the new drawer and fit it in place. This had to be done twice since it did not take the first time. It had come loose after a couple of days and we snaped it back into place. It has done fine since.

I received the drawer within 2 days of ordering it online, which was extraordinary. I removed the front of the old drawer, as instructed and placed it on the new drawer. I then replaced the drawer in the refrigerator and the job was complete. The entire experience from beginning to end was simple and completed in very little time. Had I known it would be this easy, I would have ordered the drawer sooner.

took door off. sanded rusting hinge and greased. installed door hinge washer. I had to install a larger washer over hinge bearing to help support the door where it was rusting. no sweat. works like its new. thanks to you guys for having the parts.

First I removed the old drawer front. When put the old front onto the new drawer I noticed that the two little rubber plugs had nowhere to push into as the holes were not drilled out. I got my portable drill and drilled out the holes, then I slid the drawer front into place snapped it in and pushed in the plugs.

Website was great!

The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.

To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

just like the video showed...it was excellent!!!

The job was as simple as could be pry away the old and push in the new.
Only wish I had done years ago. Tthis is a great service to customers.

The repair was very simple, I put the cover trim on the insert panel and installed it into the slot.
This is the second time I've repaired this refrigerator, not bad for a single woman.

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

Looked up troubleshooting info on your web site. Decided to replace the defrost timer. Ordered it using Paypal. Received the Shipment in about 1.5 days in Rural NC. Watched Your Video, cut off power to the fridge, removed the top self and unbolted the panel, removed the defective defrost timer, installed the new one and re-installed the panel and top shelf. Set the timer to defrost to check the operation (looked inside the freezer to see that the defroster was glowing red - it was) waited about twenty minutes to ensure that the fridge started cooling again. Fixed!

it was simple

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.