MRS20HRAW5 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Raymond from Yorktown Heights, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator too Warm
tested the thermostat, cleaned the coils, checked seals all clean. defrost timer did not cycle so replaced it but issue not resolved. even though freezer was working while refrigerator was problematic, proceeded to open freezer panel. discovered that fan was not pushing cold air into refrigerator compartment due to ice build up in connecting tubes. cleaned ice and replaced panels to positive result
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Holbrook, NY
- Parts Used:
- 5304464438, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
fridge shut down stopped running
simply watched videos provided…making it EXTREMELY simple..saved me hundreds by not having to throw it out!! running better than ever like as if it was brand new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from North Plains, OR
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer & fridge warm / condenser coils iced over
Problem not consistent. OK for 2-3 weeks, then freeze coils. Mark and observe the defrost timers manual rotating adjuster. Timer would stop mid cycle. One revolution equals 8 hours of compressor run time followed by 30 minutes of defrost. Replacing timer took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilson from indialantic, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
compressor not running
thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from WEIRTON, WV
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer frosted up and air could not circulate to the food section, causing the temperature to get warm, 55 degrees
I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Wilmington, DE
- Parts Used:
- 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was cold bit the refrigerator was warm.
Based on the diagnosis on this site I thought the 66% odds of the problem being the Defrost Timer looked pretty good, $30 including shipping versus a Sears tech phone estimate of $250-300. BINGO! Just follow the online installation instructions and don't forget to use the reset switch as described. Works like new! THANK YOU
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Glendive, MT
- Parts Used:
- 215267701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf end caps broken and replaced them
Snap Snap job done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Sunset, SC
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer worked, Frig would not cool.
Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from Chepachet, RI
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
at first auto defrost would not work so I had to take the frezer panel apart and defrost it with a hair dryer every ten days
pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Red Oak, IA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not defrosting and then warm up do to ice
replaced the defrosting timer and saved a lot of $ by doing it my self.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from Carson City, NV
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broke crisper drawer cover supports
Took off the old crisper drawer cover supports with the screw driver and put the new ones with the screw driver and small hammer (really easy)thank you to your installation instructions video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Gambier, OH
- Parts Used:
- 241559801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light socket burned out
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Tulsa, OK
- Parts Used:
- 5303300027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator-Freezer would not stay cold-frozen
I unplugged the refrigerator then removed the temperature adjustment knob from the thermostat which protrudes through the plastic cover located inside the top of the freezer compartment. Then the two hex head retaining screws were removed from the underside of the plastic cover allowing it to drop down and grant access to the bad thermostat control module which was then unplugged and removed from its mounting. The temperature probe is also removed from its sheath at this point as it's attached to the thermostat and has to be removed as well, it simply slides out of the sheath. Installation of the new part is the reverse of the removal of the old part. My refrigerator now works as good as new. Problem solved. The replacement part seemed a little bit pricey for what it is but, in my opinion, was delivered very quickly. As stated by another here, writing this report has taken longer than the repair did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford H. from Lakeland, FL
- Parts Used:
- 215473602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shelf end caps broke, needed replaced.
I watched the video from your company and within a couple of minutes replaced them. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from DEPTFORD, NJ
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refridgerator not geting cold.
Just followed the online instruction video .It was very easy.
Was this instruction helpful to you?
Thank you for voting!