FRS26ZNHW0 Frigidaire Refrigerator - Instructions

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

It was almost too easy. All I had to do was screw 4 screws into the handle, put the caps on to hide the screws and I was done. And I saved money by ordering from Frigidaire vs my local appliance store where I actually purchased the freezer.

Unscrewed the gaskets from the doors and took off. screwed the screws and put tthe sealant on t he cornors on both doors and that was it. very easy. directions were great.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I took everything out of the freezer. Removed All the shelves, took the front off of the evaporator coil compartment. Then I defrosted the evaporator coils with a blow dryer because they were basically a solid block of ice. Then removed the heater coil, installed a new one. Installed a new defrost thermostat. Put the evaporator coil panel back on. Then I turned the thermostat back up to where the fan came on and I noticed it took a few times for the compressor to continue to run. I don’t know what that was all about but eventually the compressor kicked in and everything worked like it should.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Replacing the old drawers out for the new ones was so easy that my 13 year old son took less than 15 minutes to do the job! By himself!
He pulled out the two old broken drawer,s took off the front panel,s on each, put the panel on their respective new drawer , filled the drawer up with the veggies that were in it before, and put the whole thing back in the fridge! Now my drawers work again and don't fall out or crack each time I open them! Hooray for replacement parts!!! Saved me a bundle on buying a new fridge!

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

Jonnine's husband did the repair - At first, I was stumped on the cause of the problem because I thought because I did get some ice, the pump (valve) must be working. But after pulling the dust cover back off the bottom of the fridge, I removed the dual valve. I had my wife operate the switch in the door for water and I could tell that it wasn't activating the valve at all. Ordered the valve, took 30-45 minutes to put it on. Worked like a charm. Full ice bucket now and water through the door again. Easy install.

Changed the defrost timer and the Thermostat. Still did not fix the problem. Replaced the defrost heater and now it's cooling just like new.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

Remived the old hinge with no problem. Installed new part, and found that none of the holes lined up (not even close). Had to grind old hinge apart and use it as a template to lay out and drill bolt holes in replacement part. Installed new hinge, then found that it wouldn't close the fridge door. It will hold it closed, but that's about it. What should have been a 10 minute job took over an hour,

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg