FRS23KF6EM2 Frigidaire Refrigerator - Instructions

first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Once I recieved the new filter, I enthusiastically opened the box, removed the filter from it's packaging and set it aside for quick access. I opened the refrigerator door, pushed the release button on the old filter and pulled it out. I then tossed the old filter in the trash.
Once that was done, I removed the 2 rubber caps covering the inlet and outlets on the new filter. Then, with ace precision, I guided the new filter back into the slot until it clicked. I ran the water for 3 minutes as the instructions suggested, then, had a glass of water.
Mission accomplished and it went off without a single hitch!

Glenn Walker, Simi Valley, Ca

Easy repair, except the re-install of the entire water/ice part back into the door. The original plastic water line too short to fit back into the small opening. Hint: Go buy 10 inch of new water line and a small connector. Run the new line up through the small opening, and connect to the original water line with the small connector. This made it easy to replace and test, and then cut of the excess water line.
Thanks.

Pulled the old gasket off and put new gasket/seal on by pressing firmly into slot.

Bought a new
capacitor.

Removed the trim screw on top of the door then removed the two hinge bracket bolts. lifted the door
off placed on the table. Remove the two screws on
holding the bearing bracket on the bottom of the door.
removed the bearing and replace with the new one.
Reinstalled in reverse order.

Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)

Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug.
Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.

First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

Followed the steps in the video on your site, really easy to do.

-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.