F44P21ATD0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anil from Somerset, NJ
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator was not cooling and the motor was running constantly
Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Pinole, CA
- Parts Used:
- 215846602
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Frost in freezer, fridge not cold
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from woodland, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the freezer would stick in defrost and not come out
Removed the vent cover at the bottom. Removed the screws. disconected the harnes and put the new timer in. This was a very easy fix. Thank You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from San Francisco, CA
- Parts Used:
- 218758602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shelf end caps weakened with age and broke.
I removed the shelf, took off the old ends caps, replaced them with the new ones and put the shelf back in place. No glue or tools needed and the job was completed in under 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justine from Oxnard, CA
- Parts Used:
- 218971302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The tip of the braket broke and would not longer hold the meat drawer
First, my husband removed the shelf assembly. Then he unscrewed the boken bracket. He then screwed in the new bracket and proceeded to install thecomplete shelf assembly back into the fridge. Placed the meat drawer back into correct location, to fit back into rail brackets. All done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from NEW YORK, NY
- Parts Used:
- 218971202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic rail broke.
The meat drawer is already pulled out because the broken rail could not support it. 1st I removed the shelf. Then I removed the 2 screws connecting the rail to the shelf. I then replaced the rail, screwed it together and put the shelf back in place. I put the meat drawer back on the rails and it's done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WAYNE from NOVATO, CA
- Parts Used:
- 5303288973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The supports for the crisper cover had broken and the draws would not open correctly
I watch the how to repair video on line and the repair went very quick and easy.It was just like the video,no hidden suprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from YARMOUTH PORT, MA
- Parts Used:
- 218668004
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
handle was pretty worn out. vinal coating on handle was worn and pealing
quite easy with screwdriver. I was somewhat surprised that they did not include screws as well as the small part to cover the screw hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Canton, OH
- Parts Used:
- 5304404821
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator keeps running only turns off very seldomly
Problems. Two screws holding temperature control module to the plastic case did not fit the holes in temperature controler were too big. So I used gorilla glue to help secure but it was still loose a little bit with all the connections made i turned it on but it did not work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from FORT MYERS, FL
- Parts Used:
- 5303275789
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Replace the gasket around the freezer door ($122.00 NEW GASKET)
Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinstall the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.
Was this instruction helpful to you?
Thank you for voting!