FPCI21TML3 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from MANSFIELD, OH
- Parts Used:
- 5303323480
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Replaced the old end cap with the new one. Took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Sunrise, FL
- Parts Used:
- 5303917098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Ice Make Stopped Making Ice
It was very easy. Pulled off the old valve and replaced with the new one and it started making ice right away. There are a couple of issues you need to be aware of that I am watching closely now. The old valve was a 15 watt valve. The one they sent me is a 35 watt valve. It really pressures the water into the ice maker. So much so I am getting a little leaking from the overflow. Its working so well and powering the water in so fast it starts to leak a little due to being to full. When I ordered the part, no where did it show the wattage of the valve so be careful. It works great but will have to keep an eye on it so it does not overflow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myron from West Palm Beach, FL
- Parts Used:
- 5303917098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
No water to Ice Maker
Made sure water was going into valve, shut off water to valve, removed it. removed two connections, replaced with new valve, Walla, off & running. Incidentally, rec'd new valve much quicker than I ever expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Pima, AZ
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator keeps frosting up and not cooling
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Spencer, IA
- Parts Used:
- 5303323481, 5303323480
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf clips
snapped in the one end, placed the bar in one end and the other clip on the other end and snapped it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WHITE BEAR LK, MN
- Parts Used:
- 5303917098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice maker quit
Removed dead water valve. Installed new water valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Gaylord, MI
- Parts Used:
- 5303323481, 5303323480
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
End caps broken - shelf kept falling off
Snapped the end caps onto the existing shelf, and eased the assembly into the door slots. Light tapping with a hammer was required to fully seat the assembly into the door. All in all, a straightforward and simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Matthews, NC
- Parts Used:
- 5303917098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ice maker wouldn't make ice
Needed to replace the valve in the back. My first attempt at a fridge repair. New valve went on in a flash and the ice maker is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Cleveland, TN
- Parts Used:
- 5303323481, 5303323480
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Brokern Door shelf end caps
The door shelves in the freezer door of my Frigidaire refrigerator were broken, rendering the shelves useless. I ordered four (4) end caps from PartSelect. The end caps arrived in about five days. I attached the caps to the ends of the door shelves and popped them into the slots on the door. It was a very easy repair!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Fairborn, OH
- Parts Used:
- 5303205987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Support was broken.
Removed broken and installed nw part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Chicago, IL
- Parts Used:
- 5303323481
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Unable to use shelf because retaining bar bracket broke.
Cleaned insert hole, did a dry-run, then pressed everything permanently in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Decatur, GA
- Parts Used:
- 5303323480
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
front rack broke off
Slipped out the end caps with the broken prongs from the front rack and slipped in the new end caps. (3 mins.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from San Angelo, TX
- Parts Used:
- 5308000010, 5300158289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Fan Motor was making noise and freezing up.Fan was missing one blade.
Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- doug from Franklin, TX
- Parts Used:
- 5300158289
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
bottom of fridge quit cooling
dismantled the top rear panel of the freezer and found I had the wrong part. Hand started the fan motor and it has been working fine since.
Was this instruction helpful to you?
Thank you for voting!