RS192MCH1 Frigidaire Refrigerator - Instructions

I needed to determine if the heating coil was ok. I bypassed the thermostat, rotated the defrost timer manually with a flat screwdriver until it clicked. The coil heated up and turned a glowing red. So the coil was ok. After looking at the wiring diagram located on the back, the only parts in line was the timer and the thermostat. So I ordered both, replaced them, and everything is working fine. I went online about noon on Thursday, placed the order. The shipping indicated 2-3 business days. To my surprise, they were delivered to my home on Friday, mid morning. Great service from Part Select.

I original tried to repair the motor but was not able to. I remove the screws on the back plate and removed the the back plate. Removed the shroud for the motor and screws, unplug the power connection and removed the fan motor. Installed the new fan motor and reassembled everything. The refrigerator is working great.

Replaced the refrigerator thermostat. One hex-head screw in the rear and two tabs on the front hold the thermostat cover on. The temperature knob pulls off by friction, exposing two phillips-head screws that hold the thermostat in place. Two power wires and one ground wire are held on by clips. The replacement thermostat is a different shape than the original, but it is a direct fit. This replacement eliminated the problem. The only thing that made the job difficult was not having any instructions nor any wiring diagrams for the refrigerator.

According to the information from the parts select website the thermostat and the defrost timer where ranked number 1&2 as likely to fail and cause the condition experienced. To replace the Defrost thermostat just remove the freezer bins and the lower panel covering the evaporator. Remove the old thermostat, measure the wire lengths and install the provided crimp splices. Note: the heat shrink tubing is WAY over-sized and will not shrink to the size needed. You will need another means of sealing the wire connection. Install the thermostat and replace the panel and shelves. The timer is real easy. On my model it is located under the freezer door under the kick panel on the front. Simply remove 2 Phillips head screws, unplug the old unit and install the new one. Be sure to cycle the thermostat past the defrost cycle on the timer (rotate until an audible click is heard once for the beginning of the cycle and one at the end) so that the unit will start up when power is reconnected. This resolved my problem and the unit is working great!

One of the three top comments from other replys had similar problems, so I took their advice, since the prices were resonable, I went and replaced two parts instead of just the defrost timer. If I had to do it a second time I could probably do it all in about 20 mins.

Ordered new parts, removed old parts, put in new parts. Done.

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

The temperature was slowing rising in the refrigerator section of a side-by-side. As a precaution, I changed out the defrost timer and defrost thermostat. The parts were not expensive. I then tested the defrost heating element with a multimeter and found the actual culprit was a burned out heater coil. I ordered the part one day and it was delivered by FEDEX the next day. The three parts were much cheaper than a new refrigerator and took little time to install, thanks to the Parts Select website and the how-to-install videos. Now the fridge works great and we saved having to buy a new appliance.

Part Select suggested probable causes and supplied videos of how to make the repair of a 25 yr.old refrigerator along with the specific parts to order. I was about to trash the old refrigerator but after replacing the parts for a total of about $40 and 1 hour of time it works fine now.

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.

with patience

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

I followed the advice of many people with the same problem, and replaced the Defrost Thermostat and Defrost Timer. Both repairs were relatively easy, and the problem appears to be solved. The replacement of the Defrost Timer is very easy (about 30 minutes), and I wish I had stopped at that step and waited 48 hours to see if that fixed the problem. But, I wanted to replace both parts that I had purchased - - In my refrigerator, access to the Defrost Thermostat is through the back of the freezer panel. Not too difficult to get to the area, but I had a bit of a problem in replacing the part, and might have been better-off to see if step 1 fixed the issue. The problem that I ran into is that I don't have a crimping tool, and crushed both of the connecting sleeves when trying to 'crimp' them with a set of wire-strippers. Rather than to invest in a crimping tool, I connected the wires and sealed with electrical tape - - Now that the issue is resolved, I will likely re-open and use a proper connecting sleeve (with a proper crimping tool). My advice is to buy both parts, and replace just the Defrost Timer first. Chances are good that it may fix your problem, and you are only out $20 for the second part, which you can leave in your junk drawer until you may need it some day! All in all, it was a great way to spend $40 and avoid a costly service call!

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.