MRS20HRAW2 Frigidaire Refrigerator - Instructions

Very simple...I followed the instructions given from someone on this site! I received the drawer within 2 days from purchase. I went on this site for tips to replace the plastic removable front piece. I just used a kitchen knife and gently pried the front away from the drawer and slid the front up and off. Then I slid the plastic front onto the new drawer. Very easy and quick.

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

I watched the video from your company and within a couple of minutes replaced them. Very easy.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

I unplugged the refrigerator then removed the temperature adjustment knob from the thermostat which protrudes through the plastic cover located inside the top of the freezer compartment. Then the two hex head retaining screws were removed from the underside of the plastic cover allowing it to drop down and grant access to the bad thermostat control module which was then unplugged and removed from its mounting. The temperature probe is also removed from its sheath at this point as it's attached to the thermostat and has to be removed as well, it simply slides out of the sheath. Installation of the new part is the reverse of the removal of the old part. My refrigerator now works as good as new. Problem solved. The replacement part seemed a little bit pricey for what it is but, in my opinion, was delivered very quickly. As stated by another here, writing this report has taken longer than the repair did.

Just followed the online instruction video .It was very easy.

Snap Snap job done

Unplugged the frig. Removed temp control module from frig, 1 screw with nut driver. Activated defrost timer by rotating adjustment until 2 clicks are heard. Removed two timer mounting screws, unpluged timer, plugged in the new timer, mounted it to the control module with 2 mounting screws. Replaced control module with the 1 mounting screw. Closed door and plugged it up.

pulled down the thermostat cover and unpluged the timer control and replaced it with the new part. total time to repair was about 15 min. there was a vidio on how to replace the new part that just informed me that I did it right!!!!very easy site to find what you are looking for!!!!

replaced the defrosting timer and saved a lot of $ by doing it my self.

Took off the old crisper drawer cover supports with the screw driver and put the new ones with the screw driver and small hammer (really easy)thank you to your installation instructions video.

it was great. I ordered the capacitor for my frigidaire frig and it arrived
in 3 days. plugged in the part to the compressor and my frig has been
working ever since. I spent 3 minutes ordering the part and 30 seconds
attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair
visit. thanks

It was do easy I removed the front of the drawer pleced on the new one and I was done .no tools needed.

simply watched videos provided…making it EXTREMELY simple..saved me hundreds by not having to throw it out!! running better than ever like as if it was brand new!!

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.