FRS20WRHD6 Frigidaire Refrigerator - Instructions

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

just put new bin in slots

The repair was 1-2-3-. The trim poped right into place , no tools needed for the repair. the color was a perfect match. the part was 50% cheaper than one ordered from Repair Clinic.comm very happy with the out com. Also the part was on my door step in 2days with normal shipping.

LBJ in New Jersey

Pulled the front Pull-face up off the old drawer...pushed the Pull-face down onto the new drawer--looked it over carefully and snapped it into place. Wish everything in my house were this easy to fix.

Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.

BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

Removed the back panel of the freezer. Unplugged the defrost cycle thermostat and replace with a new one.
Removed the bottom cover in front of the refrer. removed the defrost timer, plugged new timer in. manually tripped the defrost timer. checked the defrost heater for operation. Checked OK, replaced covers, works like a champ

First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

I damaged the timer while moving the fridge and did not realize it and it took 10 minutes to change out. "note" don't panic when it don't come immediately there is a dial in the front of the timer you can turn with a flat head screwdriver that will activate the timer

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23