F45ZR24JD1 Frigidaire Refrigerator - Instructions

I ordered a replacement on-line (real simple, visual aids helped more than model nos). Once I received it in the mail, I installed it (no tools required) and now my water filter and ice maker are back to doing what they do best!

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

The part’s picture on the site was not identical to the part delivered, but the function was essentially the same. It had different connectors to the outgoing tubes and a slightly different method of attachment to the refrigerator (it required 1 additional skew - not included). After verifying the part would still work, I shut off the water. Then I disconnected the two outgoing tubes. Made sure I had bucket handy to handle excess water. Then I removed the part using an adjustable wrench (1 screw) and then detached the incoming tube. Attached the incoming tube to the new part and then remounted (2 screws). And then I attached the two outgoing tubes and turned on the water. It works great and I have no plumbing experience.

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona

Unscrewed the gaskets from the doors and took off. screwed the screws and put tthe sealant on t he cornors on both doors and that was it. very easy. directions were great.

Jonnine's husband did the repair - At first, I was stumped on the cause of the problem because I thought because I did get some ice, the pump (valve) must be working. But after pulling the dust cover back off the bottom of the fridge, I removed the dual valve. I had my wife operate the switch in the door for water and I could tell that it wasn't activating the valve at all. Ordered the valve, took 30-45 minutes to put it on. Worked like a charm. Full ice bucket now and water through the door again. Easy install.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

Removed shelves ,removed panel on interior back wall with Philips screwdriver ,unplugged wire terminals slid thermostat off coil ,then reversed process to complete installation.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.