RT175GCV1 Frigidaire Refrigerator - Instructions

change the evaporator fan motor kit working perfect

Unplug the refrigerator unit from wall. I removed freezer rack, plastic light cover, the ice rack shelf on the right side, then removed the plastic back cover panel, (4) retaining screws, gently tilting the panel toward me, unplug the wiring harness by depressing the clips on the side of the plug, removed panel from unit, set aside. If the unit was froze up, so I defrosted the cooling coils carefully with a common hair dryer until it was thawed. Be careful not to touch or bend the coils , since they are very fragile and SHARP! I located the old thermostat unit attached to a straight length of coolant line. The new unit looked like the old one, so it was easy to locate. I cut the two wires of the old unit close to the round base to make sure I would have enough wire to reconnect. Since my new unit did not indicate a polarity(Neg or Pos), I just wired each wire I cut to one of the new unit. I used the shrink tubing provided and heated the shrink till it was fully melted. I double ck'd to see if the wires were basically waterproof and a good connect. Also, before I replaced the rear panel, I made sure that both wires I had spliced had a drip loop to it so water would not drip down into the newly spliced union. Also made sure the wires will not interfere with the colling fan on the back of the rear panel. Reverse the procedure in reassembling. Plug in unit, and wait and listen for the unit coming back on..I kept a regular thermometer in the upper and lower compartments. Allow 24 hrs. for the unit to return to normal operation. It may defrost several times till the whole operation is back in sync.

Emptied freezer, removed fan motor cover (2 screws), removed fan and motor (2 screws), removed old motor from bracket and reassembled with new motor, transferred fan blade from old motor to new), re-installed new fan/motor (2 screws) and reinstalled cover...

Removed screws that fastened bracket to fridge. Next, I replaced the motor and carefully lined the brackets up so the motor would rotate smoothly. Put the fan blade on the motor and screwed the brackets back on the fridge. Motor kept popping out of alignment while I was screwing the brackets back in but I kept snapping it back in till it stayed.

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

Turned off water. Took cardboard backing off lower back of unit. Unscrewed the old adaptor from the water distributor. Unscrewed the water hose connection from the adaptor. Put plumbers tape on new adaptor. Re-connected water hose to new adaptor and re-attached the adaptor to the water distributor. Turned water on, checked for leaks, and tightened adaptor to water distributor until leak stopped (approximately a quarter turn) after hand tightening. Easy, hardest part was pulling out the unit and putting it back in place!

Very easy to do, as per the video instructions.

I went online to a you-tube video to assess the problem and watch the repair. Ordered the part on sunday before christmas and had it christmas eve! Easy 10 minute repair. Four screws held the cover on. Two screws held the timer. Unplugged the old timer an replaced. Put all the screws back and . . . . Done! Easiest repair I've ever done. Parts select did a great job, good price, very fast service! One happy customer!

The drain pan fit to perfection on our Frigidaire refrigerator model FPE19V3AW1 from 1987(!!!).

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

Removed the old burned out evaporator fan, and with the model# was able to find a replacement at PartSelect. I was really surprised that you had the exact part on a fridge that old. Installed the new fan, and the fridge is working beautifully. Thanks to PartSelect I was able to save several hundred dollars.

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

Removed screws from bottom door hinge,,removed door,(don't lose washer from top door hinge when the door is removed),the new gasket wasn't too out of shape,i put fridge door on table top , loosened all the screws, pulled off the old gasket,,cleaned the surfaces, and installed the new gasket,,"Take yout time to make sure the gasket is completely and correctly under the door liner.If the new gasket is somewhat deformed,a hair dryer will work great to reshape,,"Be Careful-Do Not Overheat".I reinstalled the door , and it's working fine. NOTE; Since i removed the bottom hinge, i needed a second person to help keep the door from falling when i removed the lower hinge, and needed the second hand to do the reinstall. Have a tube of RTV Silicone Sealant on hand and follow supplied instructions.

Removed shelving, and rear panels. Replaced condenser fan and defrost thermostat. Defrost coil ohmed fine. Reassembled and plugged in fridge with thermometers inside. Freezer at 22degrees and fridge at 32 degrees. My first time repairing a fridge. the partselect videos were very helpful.

1. Unplug the refrigerator.2. Remove the storage rack and back panel in the freezer. 3. Locate the thermostat. 4. Defrost the freezer coils , i used a hair dryer. 5. Remove the thermostat from the cooling coil and then clip the connecting wires close to the unit. 6. Strip the ends of these wires and connect these wires to the wires of the replacement unit using the supplied wire connectors. 6. Heat seal with a lighter the connections using the water shield sleeves provided and further wrap connections with electrical tape. 7. Reconnect the thermostat to the cooling coil at the location it was removed from. 8. Replace the freezer back panel removed earlierand the storage rack if you have one. 9. Plug the freezer back in. My refrigerator has been working ever since the repair. There are several YouTube videos available that walk you through the diagnoses and repair process. They are very good.