LGUB2642LF1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Don from NEW BERN, NC
- Parts Used:
- 241830001
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
ice maker failure, broken auger housing
Remove ice maker, completely disassemble, being careful with the styrofoam around housing. This is a very weak part and takes much load from auger. Use a white, high strength tape to bind around the housing with, (very important) or you'll be doing this again as it is a failure point.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from ASBURY PARK, NJ
- Parts Used:
- 5303918493
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Easy peasy.
Easy repair. Great part. The hardest part was removing the fridge lower exterior door so I could get access to the icemaker. A couple of youtube videos later I realized loosen a screw, slide the icemaker out and unplug slide the new icemaker in and plug-in making sure the water spout was accurately over the water receptacle for the icemaker. Several hours later I was up to my eyeballs in beautiful clear ice cubes. Highly recommend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ORLANDO, FL
- Parts Used:
- 241829001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
ICE WOULDN'T DISPENSE FROM ICE BOX
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BRAINTREE, VT
- Parts Used:
- 218755402
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
A set scew was ordered twice.
The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from NEW WINDSOR, NY
- Parts Used:
- 241779401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Broken plastic mullion hinge. Mullion was not operating correctly.
Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Therese from Homer Glen, IL
- Parts Used:
- 242079701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
clear door bins cracked
slid shelf out, slid new bin in.1 2 3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LEHIGH ACRES, FL
- Parts Used:
- 218755504
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
No problems
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Allen, TX
- Parts Used:
- 5304469403
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ice maker quit making ice.
I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WARRE from MADISON, IN
- Parts Used:
- 241801801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper dropped and broke. ordered replacement crisper drawer.
Removed new replacement crisper from packaging. Washed crisper in warm soapy water. Rinsed & dried crisper. Aligned crisper drawer with tracks on crisper shelf and slid crisper in until front panel was in home position. Slid crisper full travel in & out a couple of times to check not only for correct travel but also travel stops. Adjusted crisper setting, placed produce into crisper, closed crisper, & closed refrigerator. WARNING do not slam, drop, or otherwise mishandle crisper. It's only plastic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Harrison, AR
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
read out on refridgerator said to order
it is a very simple process. pull out the water filter. put in the new one after removing the plastic tops. slide the filter in place pushing to set it in place. run water through water spout on door of fridge for about 3 minutes or until all the air bubbles are out. and there you are ready for a drink of water.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LESTER from KITTERY, ME
- Parts Used:
- 242011701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old bin -door was broken
remove the old one and simply placed in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Shady Hills, FL
- Parts Used:
- ULTRAWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter needed to be changed
Push in on filter and it releases pull filter out. Slide new one in push in and it locks it. Run water for 2 minutes and it is finished
Was this instruction helpful to you?
Thank you for voting!