LGUI1849LE1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from NEWBURY, VT
- Parts Used:
- 240364787
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
broken crisper cover--not glass part
replaced broken one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from ROYSE CITY, TX
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Freezer wasn't cooling - compressor not engaging
Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from ONTARIO, CA
- Parts Used:
- 241839407
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Only one way on my fridge the two ovals snap into place
Just pushed the grill on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GUNTERSVILLE, AL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Water inlet valve stuck open
Turned off water to inlet valve. Unbolted valve from back of unit, disconnect water supply line from valve, disconnected water line to ice maker. Put on new compression ring around water supply line. Pressed ice maker line into new valve, installed valve back on unit, then connected main supply line to valve. Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from SHINGLETOWN, CA
- Parts Used:
- 242015201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Scratch on stainless frig door.
Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Newberry, SC
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from WARRINGTON, PA
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cracked shelf
Snapped it in shelf in designated slots
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- will from bushnell, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer froze up/ Fridge ran warm
Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from HENDERSONVLLE, NC
- Parts Used:
- 242077705, 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
EVAPORATOR FAN MOTOR & BLADE
The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pilesgrove, NJ
- Parts Used:
- 240360801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost the temperature control know
The knob came in the plastic package. It was the correct part. I opened the package and placed the knob on the prongs. Now it works fine.
Thanks
John S.
Thanks
John S.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from EAST JORDAN, MI
- Parts Used:
- 241733911
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
You have sent the wrong part for the THIRD time. You have sent aaccess cover that is TWO INCHES too short. It does not cover the opening, and you will not answer your phones.
There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Lockport, NY
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One blade broke from condenser fan
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Nevada, IA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken freezer door gin
Hah! It took 1 minute to open the package and 10 seconds to install. The shipping response was incredibly fast. Great Service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Rio Rancho, NM
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old refrigerator door shelf broke
Installing the new shelf was easy.
Was this instruction helpful to you?
Thank you for voting!