LGHT1837LP1 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Salvador from SANTA ANA, CA
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MONTGOMERY, IL
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cristina from MARLBOROUGH, MA
- Parts Used:
- 242193213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Old gasket was torn and falling out
I removed the old gasket and cleaned the area. Then I started at the bottom and pressed the new gasket into the door. You must use firm pressure and go all around. It does get tricky hear the end as it seems like there is excess, but it will fit. Just keep using firm pressure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from ELKHART, IN
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right side meat drawer rail cracked
1] Pulled the meat drawer out. 2] Removed the shelf holding the meat drawer. 3] Unscrewed the right side rail. 4] Installed the new rail and screwed in place. 5] Re- installed the shelf and meat drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from POMONA, CA
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken right side rail on meat drawer
Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benton R. from Elkton, VA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hook on end of snap-on freezer bin broke.
The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from VENICE, FL
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Cracked part causing crisper drawer to stick
Remove items on shelf, in crisper drawers and clean all items including the refrigerator bottom before replacing with new part! Looks like a new refrigerator inside now ????
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SHERIDAN, IL
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Water Inlet Valve not sutting off
very easy, 1 screw, 2 tube connectors, hardest part was pulling refer. out of enclosure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from New Fairfield, CT
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper glass shelf shattered during cleaning.
Extremely easy repair for a 76 year old woman. I just followed the very clear video instructions provided with my order and my fridge was as good as new within 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONALD from TOPEKA, KS
- Parts Used:
- 240337103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refrigerator crisper pan broken
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from HASKELL, NJ
- Parts Used:
- 241839405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
bought brand new and kick plate was missing
just snap it on
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICOPEE, MA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None fit perfectly
Just slid it down into place.
Was this instruction helpful to you?
Thank you for voting!