GLHS38EJQ1 Frigidaire Refrigerator - Instructions

REMOVE ALL SCREWS ON THE TOP INSIDE OF THE REFRIGERATOR, IT WAS A LITLE BIT TRICKY TO FIND OUT HOW REMOVE THE PLASTIC BECAUSE THEY WAS SOME CLIP AND SLUT HOLE. NEED TO BE A LITLE BIT HANDYMAN TO DO THAT JOB. GOOD LOCK

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Removed new door gasket from box, installed on three side relatively quickly. The last side took some time, the pair of pliers and wiggling to get it to seal to the door frame.

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

Remove the drip tray to expose the 3 screws...remove screws and then 3 more screws to remove broken actuator and replace with new part.....very easy repair!

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair

All I did was remove the drawer, remove one screw. I took out the old slide, installed the new one and replaced the drawer. Quick and easy