FRT18IL6JM6 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from BASKING RIDGE, NJ
- Parts Used:
- 215846604
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Refrigerator had not been cooling
Discovered the coil was covered with 1/2 inch of ice because defrost cycle had not been working. Replacing the defrost timer and melting ice with hair dryer fixed problem. Hooray!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from SALOME, AZ
- Parts Used:
- 5303918202, 215846604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Freezer compartment works but gets frost and ice buildup. Then the refrigerator compartment fails to get cold. Milk would spoil but freezer stayed frozen.
After watching numerous YouTube videos I realized that my problem was either the timer or the thermostat. I purchased both for above $70 total and decided it was worth the gamble to self- repair it instead of buying a new refrigerator for $700 plus taxes and delivery charges. The videos were right on with excellent directions for replacing these 2 products. Only has one problem… the shrink wrap that came with the thermostat is very thick and will NOT shrink with a hairdryer. I hade to run to ACE Hardware to buy a heat gun and more shrink wrap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Damascus, PA
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Warter valvr cracked
It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump
Fell problem is in the ice maker went it dose make cubs they don,t dump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from ARANSAS PASS, TX
- Parts Used:
- 5308000010
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bettie from Toledo, OH
- Parts Used:
- 240358008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Had no freezer shelf.
I had to cut a little of of the ends of the shelf to make it fit. I used an angle grinder to get the job done and the shelf fits perfectly. By the way I paid for 3-5 day shipping and got it the very next day can't ask for better service than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Micu from MOJAVE, CA
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Every thing went smooth
But I have back ground mechanical skills, I did see the video one time, and everything went smooth......
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from South Lyon, MI
- Parts Used:
- 240358008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer came with no shelf
The shelf fit perfectly right out of the box. It was as if it was made for it. No tools needed except for the box cutter to open the shipping carton.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dante from SOUTHOLD, NY
- Parts Used:
- 241798231
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice Maker ffss2614qpo
Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.
. Very easy 1-2-3 it was out and new one in..........??.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- José from ORLANDO, FL
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge was cooling down enough the heating defrost was bad
I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Andover, CT
- Parts Used:
- 5304507147
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Refrigerator door was not sealing correctly.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnnie from NEWPORT, TN
- Parts Used:
- 241872512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Gasket broke on bottom
Popped the old one out and pressed the new one in. Very easy. Pressed new one in my hands. Fits in a channel. Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JUSTIN from NEW BRAUNFELS, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Top cools bottom is weak
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dianna from HALE, MO
- Parts Used:
- 240364787
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My Crisper cover was cracked and broken.
I ordered the replacement part. Cleaned out the bottom of my refrigerator, popped in the new part, replaced the food and was siting in my recliner in under 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RALPH from PARIS, KY
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken
Slid the old shelf out. Attached meat drawer to new shelf and slid it in.
Was this instruction helpful to you?
Thank you for voting!