FRT18IS6JQ2 Frigidaire Refrigerator - Instructions

First download schematic from frigidaire.com and watch a few youtube videos on fixing refrigerators .At first my guess was the timer was stuck on the defrost mode .However after studying the schematic I checked to see if the power was being sent to the compressor through the starter ptc .The 110 v was there after pulling off the connector .Also the condenser fan was on confirming this . however the compressor was stone cold .the compressor has 3 inputs whose resistances across all seemed good (see youtube videos) so it was probably the ptc starter or the 15microfarad capacitor .I changed the capacitor first -not the problem .then the ptc starter .immediatey the compressor started warming and after a few minutes cold air was being blown in .Very satisfying !

Our refrigerator door shelf retainer had broken on the side which basically put one shelf out of commission in our fridge. I looked up our fridge on partselect and found the correct retainer and ordered it. The part came very quickly, within just a few days. If fit perfectly and I'm very happy with the part, the speed of delivery, and ease of ordering. I will definitely use partselect again.

The part was perfect for the door. It snapped into place
on the door.

I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

removed ice maker,,and screws holding back of freezer cover,unplugged wires and removed the cover and fan.wow,only wire to element had come unplugged!went ahead and replaced thermostat,and defrost timer,both were easy to do

grab gasket on a corner and pull...new gasket push raised rib into grove....your Done!!!

The repair was a simple replacement. The problem was that after waiting three weeks for the new drawer to arrive I had to call the company and ask what the delay was?? They said the first order was lost in the mail?? Second order arrived within a week. But we didn't enjoy having to wait this long.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process

No big deal. Placed the order, got the replacement. Put them in and that was that! The great thing is, I have a perfect refrigerator for new renters. It would have been a lost rent without these easy to get parts. Thank you.

Easy peasey just slipped it in

I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up water but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

Turned off fridge circuit breaker
Removed all food from freezer and put in cooler.
Removed shelves from freezer
Removed ice maker
Removed 2 hex head screws
Tilted back evaporator cover and tried to unplug connection.
Found connection was iced over with a huge block of ice coming from water inlet to ice maker
Spent several hours trying to melt and chip away ice without damaging fridge.
Finally was able to break up ice with long flat head screwdriver and hammer.
Unplugged connector and was able to remove evaporator cover.
Cut wires near thermostat and removed
Stripped wire as needed and crimped new thermostat in place.
Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected.
Reconnected evaporator cover connection and reattached cover.
Reinstalled ice maker
Reinstalled shelves.
Put food back in
Turned circuit breaker back on.