FRS6LF7JS3 Frigidaire Refrigerator - Instructions

First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.

Simply replaced the drawer cover (frame) of that shelf. Removed crisper drawer, removed glass shelf, removed frame, placed new frame in, then glass, then drawer. Very easy.

1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

This occurred on Sunday and I ordered the part Sunday afternoon. By Tuesday afternoon the replacement was back at work. It just slipped into place, without any tools or fuss.

It was very simple. I order the complete Ice Container with Auger. It is great that it is already assembled. I just took out the old one and slipped the new one in. It has been working great ever since. I am just sorry that I waited so long to order the part. It was already like four months that the Auger started to give out on me. Thank You for everything, especially the delivery time.

Turn off power to refrigerator. Remove dispenser tray and three screws. Lift up on cover and pull away from fridg. Next remove control circuit board, use magnetic screw driver on very small screws. Important to mark all wires and their location before removing. Remove water tube from water actuator by lifting tube out of actuator,you don't have to turn water off. Next remove dispenser module and set next to new dispenser module. Then carefully remove and install parts on new dispenser module. Take your time and besure all parts installed as they were on the old module.

Reviewed the video on your website and followed the directions to the letter. Great video

The parts came within 2 days. The delivery was great. I took the food off the door, then removed the top hinge. Lifted door off bottom hinge and laid the door on a blanket on the floor. I then had access to the closing mechanism top and bottom that is just two plastic cams that lift the door as it opens. The weight of the door then is used on the cams to help close the door with the appliance level. It was very simple and assembly was just reverse order.

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

I pulled the shelf unit out and removed the screw that held in each side. The old rails removed easily and the new ones installed just as easily. I put the shelf back in and slid the new meat drawer in and it was done - much to the delight of my wife. Parts Select has a great website. It was my first time and I read one of these with the exact problem I was having. I ordered the parts, which came quickly. Everything easy and worked great! I'm a happy customer.

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

I pulled out all the screws and from the freezer side and remove the panel, then I located the thermostat snap the old one out and put the new one in.

pulled old gasket out of groove in door. Put vaseline on slotted part of gasket that fits in groove of refri. door Put some vaseline on gasket surface that would be on the hinge side of door, so it would close with ease. Had no problems at all. Thanks

P.S. Sorry about not having the model No.
The Part No was PS1991324 Magnetic Gasket for Refr side of a Freezer/Refrigerator FRIGIDAIRE There are no screws to remove on this model. Just start at one corner and begin pulling old gasket out of the groove of the door.

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill