FRT17G4BQB Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cathleen from Potomac, MD
- Parts Used:
- 240383901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf bin fixture broke off
This was the easiest thing to repair in my house! All I needed to do was to snap the appropriate new shelf in the place where the prior piece was and we were back in business. A caveat to anyone else who might try it-get your Mfgr/model number straight as well as measure the length of the shelf to be replaced. Since my brand was not listed in the pull-down menu for replacements, the first time I ordered the shelf replacement piece, I ordered the shelf that looked exactly like the one I was replacing however the replacement was a few inches too small! Thank you PartsSelect for an easy return policy and your guidance when I called
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from pensacola, FL
- Parts Used:
- 240530811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken meat drawer
new drawer was received within 2 days and was extremely simple to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W. Noah from Leominster, MA
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Kid broke to bottom door rack
This was so easy it took longer to open the door than it did to install the rack. WOW. Nice to see something fits without messing with it. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from VENICE, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator evaporator coil was icing up
The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SENECA, SC
- Parts Used:
- 240530701
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Matching up the mounting screw.
A single screw holds the part in place. The ONLY challenge is seating the new slide so that the screw hole in the glide matches the hole in the support assembly. Initially setting the glide into place mismatched by about 1/16 of an inch toward the back of the refrigerator. Firmly grasping the new part after mating it to the two receivers on the support assembly, pull it toward you until it clicks into place. The screw should mate cleanly to the new part without any difficulty. Make sure you get the right or left side part, as they are not interchangeable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from MARYVILLE, MO
- Parts Used:
- 240337712
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed a replacement door for the dairy compartment
It simply snapped into place. No tools required. A very simple repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Andover, MN
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer support rail
replaced with new drawer support rail and put drawer pack in refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Murfreesboro, TN
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The hanging drawer support on the left side broke and I was unable to glue it back together effectively.
I cleaned off the shelf that the drawer hangs from and removed it from the fridge. I took the philips head screw from the back of the broken support rail. Put the new one on, screwed it in and replaced the shelf and drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo Ann from Ruidoso, NM
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broke meat keeper rail
Removed shelf, inverted it, removed broken part (one screw), installed new shelf rail.
Piece of cake.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Pine Hill, AL
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
frezzer iceing over and not cooling the refrigerator
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Bellville, OH
- Parts Used:
- 240383901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken bin door on rental house refridgerator
the repair was simple but the real story was the easy to read blow up diagram of the refridgerator after I entered the model no. Everything was numbered and I new exactly what I was ordering.
I will definatley buy here again.
I will definatley buy here again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Akron, OH
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wife leaned on drawer and broke support.
The first thing I did was to remove all the food from the shelf above the drawer. I removed the old support rail that is attached at the rear of the shelf by one phillips screw. I installed the new support and secured it. Partselect was a great place to purchase the part and they shipped the part quickly.
Was this instruction helpful to you?
Thank you for voting!