FRS6HR35KM2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The basket hanger is plastic and the rack tips of the basket hanger are even more delicate. Replaced basmet hanger no problem. They were expensive i.e. $70.
Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...
Was this instruction helpful to you?
Thank you for voting!
Icemaker not pushing out ice
Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Mt. Holly, NJ
- Parts Used:
- WFCB
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
change water filter
Used pliers to remove filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Spokane, WA
- Parts Used:
- 240351601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bins have been broken for several years
The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Front Royal, VA
- Parts Used:
- 240505801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Switch would not allow door to close.
Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emanuel from Coconut Creek, FL
- Parts Used:
- 241681903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice dispenser paddle broke off
Remove power from refrigerator. Pull out the drip tray below paddle. Removed the 3 screws behind tray. Gently pull control panel out and remove the ribbon cable plug from panel. Set panel aside. Remove three screws holding panel housing to door, then pull out housing slightly and disconnect harness plug behind left side of housing. Pull housing out 3-4 inches. Look at the way paddle tabs engage ice dispenser switch mechanism. Remove the left paddle hinge screw and plate and loosen the right hinge screws(these also hold the water paddle hinge) Remove broken paddle by pulling out from right hinge plate and down. Install new paddle under right hinge plate, engage new paddle tabs correctly onto dispenser switch, install left hinge plate and screw, then tighten hinge screws. Reconnect harness plug, reinstall 3 housing to door screws, reconnect ribbon plug to control panel and reinstall panel screws. Reinstall drip tray. Reconnect power to refrigerator and check operation of ice and water paddles.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Sciotoville, OH
- Parts Used:
- 241682003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I broke the lever that you npush to get water.
At first glance I didn't see the screws that would permit me to get to the actuator but I lifted the small tray at the bottom and there were two screws. Everything went easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Detroit, MI
- Parts Used:
- 241786014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer door gasket became loose
Followed instructions for this part from this site and things went well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from PHILADELPHIA, PA
- Parts Used:
- 240350649
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I took the shelf out to wash it and it broke in a million pieces
I ordered a new shelf and I put in, less than minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Imogene from Truth or Consequences, NM
- Parts Used:
- 241860803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Ice Crusher Did Not Work And The Bin Was Carroded From A Previous Owner
I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- B J from Dillingham, AK
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frost build up on evaporator
Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Ocala, FL
- Parts Used:
- 240334201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One arm on the plastic bin or tray cracked and broke.
This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Hot Springs Village, AR
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
When washing the shelf insert glass piece, it broke into a million pieces.
The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!