FPHC2399KF3 Frigidaire Refrigerator - Instructions

Repair was easy. Unplug refrigerator, turn off water to ice maker, remove back panel, disconnect water inlet valve, disconnect water supplies and electrical connections. Cut ends off tubing to modify to new part connections, connect tubing, connect electrical supplies, reinstall back panel, plug refrigerator in, turn water supply back on. We made sure that there was no ice build up in the supply tube into the ice maker and made sure that everything worked correctly before putting it all back together. It was an easy repair.

Followed the online video from this site

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

VERY EASY SLIDE OLD ONE OUT AND PUT NEW ONE IT

No repair needed just replace shelf and drawer

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Very simple less then five minutes.

Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.

I changed the defrost thermostat and the heater.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.