FKCH17F7HWB Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from westlake, OH
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
Snap the old one out, snap the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rochelle from matawan, NJ
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the door shelf snapped off and broke cheap plastic
took the shelf out of box. Opened the of refrigerator door placed shelf on door pieces that held it. pushed down on it, shelf locked it in 2 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frances from charleston, WV
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken front of door shelf bin
Opened carton....removed part....washed with hot soapy water....snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Waco, TX
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bon broken
It locks into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- hector from los fresnos, TX
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
When I was ready to instal fan motor, I noticed that there was no thread where I was supposed to screw in the bolts
When i found out there was no thread in brace where bolts were supposed to screw in, I panicked. I thought I would have to send part back or go to a machine shop to make a thread. I called a friend for help and he told me the bolts would make the thread if I just screwed them in. Sure enough, the bolts made the thread and then I just proceeded to instal motor and put refrigerator back together. It was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Clovis, NM
- Parts Used:
- 297309000, 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evaporator Fan Motor was making loud rattling sound.
Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut driver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Gilroy, CA
- Parts Used:
- 297309000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
condenser fan stop working
Replaced fan. I ordered the fan and received it the following.(-:
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HOWARD from Fort Wayne, IN
- Parts Used:
- 297282800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not turn on
replaced control board and installed surge protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Peyton, CO
- Parts Used:
- 297282800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
My freezer quit working. The power light was on but nothing worked.
I paid about $50 for a tech to come to the house to troubleshoot the freezer. He id'd the temp control unit in about 30 minutes and told me he could repair the freezer for an additional $300 or so. I told him 'no'. I looked up the part number with partselect and ordered the temp control unit for about $40 including shipping. I simply plugged in the unit and reset the rear compartment panel and gaskets. I plugged the unit in. The freezer ran but did not freeze. I inspected the rear of the freezer and found that the tech had left the compressor unplugged. I connected the compressor and turned the freezer on, It is working just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CRAIG from PRESCOTT VALLEY, AZ
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy fan
Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Grayson, GA
- Parts Used:
- 297282800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
unit dead except for the light
Found voltage coming into unit but not making it through the control unit. Thermo switch could easly be bypassed with no results so only thing left was the control mod. It was worth the $51.00 guess , ordered the part with credit card about noon, the next day Fed Ex came to the door about 2 PM the freezer was running by 2:30. Very impressed by everyone envolved. Spent the rest of the day bragging about my repair ability. Felt good to hear that baby fire up. Thanks again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Satellite Beach, FL
- Parts Used:
- 297309000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fan would not start occasionally
I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alejandro from Auburn, AL
- Parts Used:
- 240350608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper glass broke in thausand peaces
it was easy my wife did it wen i went to the fridge it was already installed. thank you!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lagrange, IN
- Parts Used:
- 240338001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing door shelf bin
fit right in no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Admirald from North Lauderdale, FL
- Parts Used:
- 240350608
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper glass shattered while cleaning
Insert new glass into slot. Took less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!