FGHS2355KE2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Eastlake, OH
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Fridge leaked water all over my kitchen
I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I went and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from ROGERS, AR
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer was cooling, but refrigerator was not cooling all the time. Evaporator fan was running, so decided to try new thermostat.
Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cloid from HOOVER, AL
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice Director Door Broken In Half
I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from LANCASTER, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
LEAKED WATER AFTER USING WATER DISPENSER
DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Verdell from NEW ORLEANS, LA
- Parts Used:
- 5303918214
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Refrigerator was icing up
I changed the defrost thermostat and the heater.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from SHINGLETOWN, CA
- Parts Used:
- 242015201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Scratch on stainless frig door.
Can't supply any info that would be helpful. Ordered a " badge" that covered 100% of the scratch and stuck it on. Scratch now covered and problem solved. Thanks for asking.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from THE PLAINS, OH
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dispenser Crusher Housing was broken
I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23
Was this instruction helpful to you?
Thank you for voting!
Ice Crusher Houseing cracked broke into pieces
Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Ravenswood, WV
- Parts Used:
- 241850615
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from LIVERMORE, CA
- Parts Used:
- 241885001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The ice crushing housing was broken.
The repair went easily after watching the video, took me less than an hour to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Berthoud, CO
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Part broke though normal use
Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stefan from LAKE WORTH, FL
- Parts Used:
- 241786015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Removed old gasket and installed new one by pushing the gasket in the door groove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John A from BRUNSWICK, GA
- Parts Used:
- 242252702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No water to ice maker
Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ville from SAN JOSE, CA
- Parts Used:
- 241547902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker doesn’t work
Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Woodrow from INDIANAPOLIS, IN
- Parts Used:
- 241973101
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Originally part was broken
Removed the glass top, replaced on new part. Then placed back into refrigerator.
Was this instruction helpful to you?
Thank you for voting!