FGHS2367KB2 Frigidaire Refrigerator - Instructions

I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!

This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.

I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

I began by replacing the main control board and initially the fridge wouldn't even turn on/start up. After digging into the problem it turns out the newer manufactured control board won't communicate with the older secondary display board above the water/ice dispenser. It would've been extremely helpful and time saving to have had this information when I ordered the main control board. It shouldn't be difficult to create a cross reference sheet/chart as this increased my repair cost from roughly $350 to $600 and some people might opt to replace rather than repair.

Went the typical route of part replacement since I don't own an ohm meter...pull and replace one part at a time. Started with the cheaper parts first, replaced the freezer fan for $40, same problem. Replaced the defrost heater element for $40, same problem. Replaced the thermostat $15 and controller board $150 at same time, bingo problem solved. Had to defrost with the hair dryer each time, biggest pain. Had an issue finding a Utube that showed the water filter system and thermistor removal for this model, otherwise straightforward, but not a 30 minute job.

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!

removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine

push in old filter, turned to the left and filter came out. Pushed in new filter and it clicked into place. Very easy to do.

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done

Well...The freezer door bin broke while over-stuffing it with frozen deer jerky. I called my local repair shop and they quoted me what was above retail for the piece...I checked online liked the prices and felt confident to buy from parts select. I bought on a Saturday and selected the slowest shipping (I think 5 days). I got a 'notice' it shipped on Monday and had it Tuesday when I got home from work. Excellent experience.